1. Horizontal and Vertical Curves and Transitions

Curve radii and transition distances are determinants of belt, idler, pulley and splice life. Both are fixed by the conveyor profile and terminal geometry during design and are costly to correct after commissioning.

2. Vertical Curves

2.1 Convex and Concave Vertical Curves

Table 1: Convex and Concave Vertical Curves
Parameter Convex Curve (Crest) Concave Curve (Valley)
Strain distributionThe troughed belt edges sit above the belt centre, so at a crest the edges follow the longer path. Edge tension rises and centre tension falls, and can reach zero.At a valley the edges follow the shorter path. Edge tension falls and centre tension rises.
Carry strand effectBelt tension presses the belt onto the idlers through the curve. Idler load is the static load plus a radial component proportional to tension and inversely proportional to radius.Belt tension pulls the belt away from the idlers (bow-string effect). Contact load falls through the curve and reaches zero at the lift-off condition.
Return strand effectThe return strand is also pressed onto the return rolls. Return roll load rises through the curve.Return roll contact load also falls. The return strand carries no material, so belt self-weight alone resists uplift, and the strand is more prone to lift-off than the carry strand at similar tensions.
Governing load caseFully loaded start-up for edge tension and peak idler load. Fully loaded steady state for idler L10 life. Empty belt at running tension for centre tension.Base design on the partial-load condition producing peak tension while the curve section is empty, where tension is highest and restraining weight is least. Also evaluate empty-belt start-up.
Failure modesPermanent edge elongation, edge tearing, longitudinal creasing and centre buckling on loss of centre tension.Lift-off from the idlers with impact on overhead structure, loss of trough profile, spillage and tracking instability. Edge buckling at low tension.
Idler pitch through the curveReduce pitch through the curve to limit the radial load carried by each idler set. Pitch has no effect on the belt-stress minimum radius.Pitch has no effect on lift-off, which is set by tension, material load, radius and belt mass. Where calculation shows lift-off, increase the radius or reduce tension at the curve. Fit hold-down rollers only as a last resort.
Remedial measures where radius is constrainedReduce trough angle through the curve, which lowers the belt edge and reduces the radius required.Fit hold-down rollers as a last resort.
Commissioning verificationInspect belt edges for elongation marking and cover cracking.Inspect belt-lift clearance to overhead structure during empty start-up and the partial-load case.

2.2 Load Cases and Design Checks

Evaluate every applicable check against every applicable load case. The largest minimum radius returned by any check governs the curve design.

Table 2: Load Cases for Vertical Curve Analysis
Load Case (LC) Operating Condition Material at Curve Belt Tension Basis Typically Governs
LC1Empty belt, steady running and start-up at maximum drive accelerationNoneEmpty running tension and maximum dynamic starting tension at the curveConcave lift-off at starting tension. Convex centre tension and concave edge slackness at running tension.
LC2Partial load. Loading pattern producing peak tension at an empty curve, e.g. flat section loaded, curve and incline empty.NonePeak tension from material drag on loaded sections adjoining the empty curveConcave lift-off. Usually the worst case. Highest tension coincides with least holding mass at the curve.
LC3Fully loaded, steady stateFull design loadSteady-state operating tensionConvex material stability. Convex idler L10 life.
LC4Fully loaded start-upFull design loadMaximum dynamic starting tension at the curveConvex edge tension. Convex peak idler load.
LC5Stopping, aborted start or holdback engagementPer dynamic analysisTransient tension from the dynamic analysis, including drift-back arrest on inclinesAny curve near drives, brakes or holdbacks. Repeat the tension-dependent checks where transient values exceed starting values or fall below running values.
Table 3: Concave (Valley) Vertical Curve Checks
Check Failure Mode Addressed Load Cases Notes and Design Rules
Static lift-offBelt lifting off the idlers during high-tension events.LC1, LC2, LC3, LC5Set material load to zero for the empty-belt and partial-load cases. The minimum radius is the local belt tension divided by the weight per unit length of belt and material at the curve.
Dynamic lift-off (centrifugal effect)Belt lifting off the idlers at operating speed.As static lift-off, at full belt speedCentrifugal force acts outward from the centre of curvature, downward at a valley, and improves belt seating. The dynamic radius is always smaller than the static result, so the static check governs. Retain as a verification step only.
Edge slackness (belt stress)Edge buckling and waviness from loss of edge tension. Centre overstress in high-modulus belts.LC1 at running tension, at the lowest-tension location in the curve. LC4 and LC5 for the companion centre tension.At a valley the edges follow the shorter path, so edge tension falls and centre tension rises. The edge tension drop grows with belt modulus and trough height and shrinks with larger radius. Set the minimum radius so the edges remain tensile. Check the companion centre tension against the allowable working tension. Rarely governs for fabric belts. Can govern for steel cord belts at low-tension locations near the tail.
Belt seating and trackingBelt wander, spillage and off-centre loading from reduced idler contact pressure.LC1, LC2High tension with low mass reduces the normal force between belt and idlers even where full lift-off is avoided, weakening the self-centring action of the troughed profile. Verify adequate seating pressure through the curve. Do not place training idlers, belt weighers or loading points within it.
Lift clearance and containmentBelt striking hoods, walkways, cable trays or structure during a transient lift event.LC5Where momentary lift is accepted during rare transients such as an aborted start, calculate the lift height and verify clearance to overhead structure. Provide belt containment (inverted or hold-down rollers) where clearance cannot be achieved. These rollers introduce top-cover wear and are a last resort.
Geometric placementCompound belt stresses from overlapping curvature and troughing effects.AllKeep the curve clear of troughing transitions at head and tail pulleys, loading zones, trippers and belt weighers. Locate concave curves in low-tension zones where the profile allows.
Table 4: Convex (Crest) Vertical Curve Checks
Check Failure Mode Addressed Load Cases Notes and Design Rules
Edge tensionOver-tensioning and rupture of the outer belt edges. Splice edge failure.LC4, LC5Derived from elastic strain compatibility. The edges travel a longer path over the crest, so edge tension rises above the mean belt tension. The rise grows with belt modulus and trough height and shrinks with larger radius. Evaluate at the maximum-tension load case, normally fully loaded start-up, and hold the edge tension within the allowable working tension including the splice rating.
Centre tensionCentre buckling, longitudinal creasing and repeated-bending carcass fatigue.LC1 at running tension. LC5 where stopping reduces tension at the curve.At or below zero tension the belt centre buckles, and repeated bending fatigues the weft yarns and carcass. Hold the centre tension above the sag-limiting tension where practicable.
Idler loadIdler bearing overload and reduced L10 life within the curve. Accelerated cover wear at idler junctions.LC3 for L10 life. LC4 for peak load against the idler set rating.The belt presses onto the idlers through a crest, adding a radial load that grows with belt tension and idler pitch and shrinks with larger radius. Add this to the static idler load and check against the idler set rating. Reduce idler pitch through the curve where needed. Elevated contact pressure at the wing-roller junctions accelerates junction fatigue and cover wear.
Material stability over the crestMaterial lift, spillage and segregation as the load passes over the crest at speed.LC3, at full belt speedCentrifugal force at a crest acts away from the belt, unloading the material. Where the centripetal demand at belt speed approaches the gravitational component holding the material down, the load becomes unstable, fines and lump separate, and spillage follows. Size the radius so the material remains seated with margin at maximum belt speed. At a near-horizontal crest the limiting radius is belt speed squared divided by gravitational acceleration, approximately 3.7 m [12 ft] at 6 m/s [1,200 fpm], so this check governs only where belt-stress radii are small.
Geometric placementCompound belt stresses from overlapping curvature and troughing effects.AllKeep the curve clear of troughing transitions, loading zones, trippers and belt weighers. Locate convex curves away from peak-tension zones where the profile allows, since edge tension is the curve-entry tension plus a geometric increment. At low tension the centre-tension check governs instead.

3. Horizontal Curves

Using a single continuous belt for a directional change eliminates transfer towers and the associated capital cost, dust generation and maintenance. Horizontal curve radii commonly range from 1,000 to 5,000 m [3,300 to 16,400 ft].

3.1 Curve Mechanics

When negotiating a curve, longitudinal belt tension acts to straighten the belt, generating a resultant force directed toward the inside radius. The belt follows the curve by in-plane bending, which stretches the outer edge and relaxes the inner edge. Keep the inner edge in tension at the lowest-tension load case. The tension resultant displaces the belt laterally across the idler rolls until the restoring forces balance the radial load.

The restoring mechanisms are the gravity component from idler banking, the self-centring effect of the troughed profile (the belt climbing a wing roll generates a gravity restoring force) and belt-to-roll friction. Friction varies with moisture and contamination. Do not rely on it as the sole restoring mechanism.

Although centrifugal force acts on the material, the inward component of belt tension predominates at operating speeds. At 5 m/s [1,000 fpm] on a 1,500 m [4,900 ft] radius, centrifugal acceleration is less than 0.02 m/s2 [0.07 ft/s2] and is negligible in the lateral force balance.

3.2 Equilibrium and Radius Selection

Size the radius from a first-pass balance between the inward tension resultant and the outward gravity component from banking.

Formula 1: Horizontal Curve Equilibrium Radius

Metric: R = T / (m * g * SIN(beta))
Imperial: R = T / (w * SIN(beta))

Where:

  • R = Curve radius (m) [ft]
  • T = Local belt tension at the idler station considered (N) [lbf]
  • m = Combined belt and material mass per unit length on the strand (kg/m)
  • w = Combined belt and material weight per unit length on the strand [lbf/ft]
  • g = Gravitational acceleration, 9.81 (m/s2)
  • beta = Idler banking angle (deg)

Note: Rearranged from the equilibrium condition SIN(beta) = T / (R * m * g). Friction and trough self-centring are ignored, so the radius is conservative.

Engineering Takeaway: Required radius is inversely proportional to the sine of the banking angle, so increasing banking from 4 to 8 deg approximately halves it. Outward drift of the loaded belt at minimum tension sets the upper limit on banking.

Evaluate the balance at every idler station through the arc, using the local tension for each load case, and design to the worst-case envelope. Locate curves in low-tension regions of the tension profile where the alignment permits, since required radius is directly proportional to local tension.

3.3 Superelevation of the Carry Strand

To counteract inward tracking, raise the inside of each carry idler set through the curve. Superelevating (banking) the idlers directs a gravity component of the belt and material mass toward the outside of the curve.

Tilt the carry idlers progressively from 0 deg at the tangent point, increasing by 1 to 2 deg per idler frame, and hold the full superelevation (typically 4 to 8 deg) through the constant-radius arc.

3.4 Superelevation of the Return Strand

Bank the return idlers to their own equilibrium requirement. The return strand carries no material, so its tension-to-mass ratio, and therefore its required banking angle, is often equal to or greater than that of the loaded carry strand.

Flat return rolls provide no self-centring, so fit two-roll V-return idlers (typically 10 to 15 deg) through the arc to restore a centring mechanism and retain the banking geometry.

3.5 Governing Load Cases

The empty belt at maximum tension usually governs inward drift, because the tension-to-mass ratio is highest when only belt mass is present. The fully loaded belt at minimum tension governs outward drift over the banked idlers.

Check both against the transient tension envelope from the dynamic starting and stopping analysis, including aborted starts and drift-back, not the steady-state tensions alone.

4. Idler Transitions

The transition distance is the conveyor length between the last fully troughed idler and the flat terminal pulley. The troughed belt edges sit higher than the centre and travel a longer path to reach the pulley.

Table 5: Mechanical Failure Modes From Insufficient Transition Distance
Feature Edge Stretch (Over-Tensioning) Centre Buckling (Loss of Tension)
Stress conditionEdge strain exceeds the elastic limit.Tension drops to zero or enters compression.
MechanismThe edge travels a longer path, stretching outer warp yarns or steel cords until they permanently yield.Over-tensioned edges carry a disproportionate share of the load, unloading the centre.
Visual symptomsOn the flat run, edges are longer than the centre, producing permanent edge wave (flapping edges).The belt centre buckles, creating a longitudinal crease.
Resulting failuresTracking instability and splice failure at the outer edges.Repeated-bending fatigue of the weft yarns and carcass.

4.1 Pulley Elevation Geometry (Half-Trough versus Full-Trough)

The vertical elevation of the terminal pulley relative to the centre idler roll controls how the geometric strain is distributed.

Table 6: Terminal Pulley Elevation Geometries
Configuration Geometry Strain Distribution Application Trade-Off
Full-trough depth (flush pulley)Pulley top flush with the top of the centre idler roll.The belt centre travels a straight path with no additional strain. All geometric strain concentrates at the edges.Tail pulleys. A flat, level belt line through the loading zone reduces lift-off and spillage at the skirtboards.Requires the longest transition distance.
Half-trough depth (elevated pulley)Pulley top elevated one-third to one-half of the trough depth above the flush position.Raising the pulley shortens the edge path but deflects the belt centre upward. Strain is shared between edges and centre, reducing the required transition distance by approximately 50%.Head and drive pulleys, where a level belt line is not required and the shorter transition reduces structure length.Elevation above one-half of the trough depth reverses the strain distribution. The over-tensioned centre bears on the centre roll of the final troughing sets, damaging the bottom cover, and the slack edges risk edge buckling.

4.2 Transition Distances

As the troughed belt flattens onto the pulley, the differential edge path length forces a tension redistribution across the belt width. Edge tension rises and centre tension falls.

Table 7: Conveyor Belt Minimum Transition Length Criteria
Criterion Description Critical Location Consequences of Failure
Edge tensionTension redistribution loads the edges. Hold operating tension plus the transition increment within the rated working tension.High-tension locations, e.g. head and drive pulleys. Small tension margins require longer transitions.Edge rupture, accelerated edge wear and edge fatigue.
Centre bucklingAs tension shifts to the edges, the centre unloads. Keep centre tension tensile through the transition.Low-tension locations, e.g. tail and return pulleys. Edge margin is generous but centre tension is already low.Centre buckling, collapsed profile, excessive sag between transition idlers, mistracking and spillage.
Splice strainEvery splice passes through every transition on each belt revolution and carries differential strain between edge cords (high stretch) and centre cords (low stretch). The splice is the weakest element under this strain. Check the transition edge tension against the splice rating.All transition zones (head, tail, tripper and take-up pulleys).Splice deformation, cord pull-out and splice failure.

Where belt modulus data is unavailable at preliminary design, approximate the minimum transition distance as the belt width (W) multiplied by the applicable factor.

Table 8: Minimum Transition Distances as a Multiple of Belt Width
Transition Geometry Trough Angle (deg) Fabric, Tension Greater Than 60% Fabric, Tension 60% or Less Steel Cord, Tension Greater Than 60% Steel Cord, Tension 60% or Less
Half-trough (elevated)200.90.82.01.6
Half-trough (elevated)351.61.33.22.7
Half-trough (elevated)452.01.64.03.2
Full-trough (flush)201.81.44.03.2
Full-trough (flush)353.22.46.65.2
Full-trough (flush)454.03.08.06.6

Note: Interpolate linearly for unlisted trough angles. These multipliers are envelope values, not substitutes for belt stress calculation.

4.3 Transition Idler Placement Rules of Thumb

The belt leaves the terminal pulley flat and reaches full trough at the first fully troughed carrying idler. Across this distance the edge is stretched above its neutral length and the centre is relaxed. Transition idler sets at intermediate troughing angles hold the belt to a controlled profile, limiting edge strain and centre sag, reducing edge buckling and maintaining the skirt seal.

Limit the gap between successive transition idlers, and between the pulley and the first idler, to the standard carrying idler spacing (typically 1.2 to 1.5 m [4 to 5 ft]). Where the transition distance would leave a larger gap, insert additional intermediate-angle sets to maintain belt support.

Table 9: Intermediate Transition Idler Requirements
Carrying Trough Angle (deg) Minimum Intermediate Sets Intermediate Angles (deg)
200Not required
35120
45235, then 20

Note: Angles are listed from the fully troughed idlers toward the pulley. Add sets beyond this minimum where the spacing limit above requires.