1. Feeder, Hopper and Bin Design
Feeders extract bulk material from hoppers, bins, or stockpiles, operating under higher shear and tensile loads than standard transfer conveyors. A feeder shears a layer of material from beneath a static, consolidated head.
2. Feeder Type Technical Comparison
Specify belt feeders for pre-screened or secondary-crushed material (lump size typically less than 300 mm [12 in]), head heights less than 10 m [33 ft] and applications requiring higher extraction speeds.
Specify apron feeders for Run-of-Mine (ROM) extraction from dump pockets, primary crusher feed under deep bins and applications where lump size, impact severity or head load exceeds belt feeder limits.
| Parameter | Apron Feeder (Unsealed) | Apron Feeder (Sealed) | Belt Feeder | Hybrid Feeder (Pan-Belt) | Drag Chain Feeder |
|---|---|---|---|---|---|
| Description | Overlapping heavy steel pans bolted to crawler-style chains, with open physical gaps between the individual pans. | Overlapping heavy steel pans bolted to crawler-style chains, with elastomeric inserts bridging the gaps between the pans. | A continuous, heavy-duty rubber belt supported along its length by closely spaced idler rollers. | Identical to an unsealed Apron Feeder, plus a continuous rubber belt laid over the top of the pans. | Endless steel chains with attached cross-flights (scraper bars) that drag bulk material along the bottom of a stationary steel trough. |
| Maximum Lump mm [in] | 2,000 [79] | 2,000 [79] | 300 [12] | 1,500 [59] | 300 [12] |
| Maximum Drop Height m [ft] | 3 to 6 [10 to 20] | 3 to 6 [10 to 20] | 1 to 2 [3 to 7] | 3 to 6 [10 to 20] | 0.5 to 1.5 [1.6 to 4.9] |
| Typical Speed m/s [fpm] | 0.05 to 0.30 [10 to 60] | 0.05 to 0.30 [10 to 60] | 0.05 to 0.50 [10 to 100] | 0.05 to 0.30 [10 to 60] | 0.05 to 0.40 [10 to 80] |
| Practical Throughput t/h [stph] | To 10,000 [11,000] | To 10,000 [11,000] | To 3,000 [3,300] | To 6,000 [6,600] | To 2,500 [2,750] |
| Fines Conveyor Required | Yes | No | No | No | No |
| Annual Maintenance % of Installed Capital | 6 to 10 | 6 to 12 | 3 to 6 | 5 to 8 | 5 to 9 |
| Chain Life h | 25,000 to 60,000 | 25,000 to 60,000 | Not applicable | 25,000 to 60,000 | 15,000 to 40,000 |
| Pan Life h | 40,000 to 80,000 | 40,000 to 80,000 | Not applicable | 40,000 to 80,000 | 20,000 to 50,000 (trough liner and scrapers) |
| Belt Life h | 15,000 to 40,000 (fines belt) | Not applicable | 15,000 to 40,000 | 15,000 to 40,000 | Not applicable |
| Carry Roller Life h | 20,000 to 40,000 | 20,000 to 40,000 | 30,000 to 60,000 | 20,000 to 40,000 | Not applicable (chains slide on wear rails) |
| Principal Maintenance Tasks | Chain elongation monitoring. Chain and roller lubrication. Pan replacement. Fines conveyor belt replacement. | Chain elongation monitoring. Chain and roller lubrication. Pan and seal replacement. | Belt replacement. Idler inspection. | Chain elongation monitoring. Chain and roller lubrication. Pan and belt replacement. | Chain elongation monitoring. Trough liner and flight replacement. |
| Advantages | Highest impact and lump tolerance. Highest temperature capability. Proven service history across primary crushing duty. Wide vendor base and spares availability. | Deletes fines conveyor, its drive and its envelope. Reduced excavation depth. Reduced spillage handling labour. Retains apron chain and pan load capability. | Lowest capital cost. Lowest power. Continuous sealed carry surface. Shorter replacement shutdown than chain or pan change-out. Simplest access and maintenance. | Combines the high impact and lump tolerance of an apron feeder with the sealed carrying surface of a belt. Eliminates the need for a fines conveyor and its associated civil works. | Fully enclosed design contains dust and spillage. Low vertical profile reduces excavation depth. Accommodates multiple inlets or outlets. |
| Limitations | Highest capital cost. Highest installed power. Mandatory collection conveyor with associated civil depth. High machine mass. Chain replacement is a major shutdown activity. | Seal life not independently established. Elastomer temperature limit. Seal replacement labour per link. Fines ingress at the joint. Single vendor supply exposure. Return strand cleaning required. | Limited lump size and drop height. Cover wear from hopper shear. Vulnerable to sharp and hot material. Belt tracking sensitivity at low speed under eccentric hopper load. | High capital cost and heavy machine mass. The rubber belt is vulnerable to sharp and hot materials. Operating two dissimilar wear systems (chains and pans, and rubber belt) on a single machine increases maintenance complexity and spares holding. | Unsuitable for abrasive rock due to sliding wear, and for lumps greater than 300 mm [12 in] due to flight clearance. Low impact tolerance. Higher power than rolling-contact (belt and apron) feeders due to sliding friction. |
Note: Throughput, maintenance cost and component life values are typical ranges. Confirm against vendor data for the specific duty.
3. Mass Flow versus Funnel Flow
Undersized hopper openings induce cohesive arching, restricting discharge. Base hopper geometry on laboratory shear testing of the bulk material to quantify unconfined yield strength, bulk density as a function of consolidation stress, effective angle of internal friction and wall friction angle.
| Feature / Characteristic | Mass Flow | Funnel Flow |
|---|---|---|
| Hopper Wall Design | Hopper walls are designed steeper than the mass flow limit derived from the measured wall friction angle. Low-friction liners promote boundary sliding and permit shallower walls. | Hopper wall angles are shallower than the mass flow limit. Boundary friction is high enough that internal shear failure occurs before wall sliding. |
| Flow Pattern | Fully active cross-section during discharge. Follows a first-in, first-out (FIFO) flow regime. The velocity profile is relatively uniform across the cross-section, reducing particle segregation at discharge and eliminating stagnant regions. | Follows a last-in, first-out (LIFO) flow regime. Flow is restricted to an active central channel (core flow), while material at the periphery remains stagnant, acting as a static boundary (dead zones). |
| Impact on Feeder Tension | The transition from an active stress field (filling) to a passive stress field (discharge) produces a stable shear stress at the belt interface. Feeder draw-out forces and motor torque requirements remain predictable. | Time consolidation in stagnant zones increases bulk density and unconfined yield strength. Sloughing of stagnant boundaries induces erratic, high-magnitude dynamic loads (overpressures) on the feeder, causing chain or belt tension spikes and motor stalls. |
| Suitable Material Types | Suitable for bulk solids with high unconfined yield strength, high moisture content, high time-consolidation characteristics, or combustible or degradable materials. Specify where segregation control is a process requirement. | Suitable only for coarse, free-flowing, non-cohesive bulk solids (low unconfined yield strength) with negligible time-consolidation characteristics, where segregation or degradation is operationally acceptable. |
| Example Materials | High-moisture sub-bituminous coal, cohesive bauxite, synthetic Flue Gas Desulphurisation (FGD) gypsum, or clay-rich lateritic iron ores. | Coarse screened aggregate (greater than 50 mm [2 in]), dry silica sand, plastic pellets, or ROM materials lacking a cohesive fines fraction. |
| Common Failure Modes | Boundary wear: accelerated abrasive wear on liners due to continuous boundary sliding. Cohesive arching: occurs if the outlet width is smaller than the calculated critical arching dimension. Flooding/flushing: fine powders lacking adequate residence time for deaeration become fluidised, leading to uncontrolled two-phase flow. | Stable ratholing: occurs when the critical rathole diameter exceeds the diameter of the active flow channel. Dynamic overpressures: structural shock or feeder overload caused by massive sloughing of over-consolidated dead zones. Time-consolidation caking: chemical degradation, oxidation, or excessive yield strength development in stagnant regions. |
4. Wall Friction Angles and Liner Selection
Mass flow requires hopper walls steeper than the limit set by the wall friction angle. Low-friction liners permit shallower walls and reduce vessel height, subject to the wear, impact and temperature limits in the table below.
| Material | Friction Coefficient mu | Hardness and Wear Resistance | Impact Resistance | Flow Characteristics | Typical Applications | Environmental and Temperature Limits | Relative Cost | Installation |
|---|---|---|---|---|---|---|---|---|
| Mild Steel | 0.40 to 0.50 | Baseline wear resistance. | Provides structural impact resistance. | Requires steeper walls than polished or polymer liners. Oxidation increases surface friction. | Dry, non-abrasive materials. Structural bin shells. | Corrodes in high-moisture environments. | 1.0x | Standard cutting, forming, and welding. |
| Ultra-High Molecular Weight Polyethylene (UHMWPE) | 0.15 to 0.25 | Low wear resistance. | Resists impact fracture. Gouges under particles exceeding 150 mm [6 in]. | Promotes mass flow and mitigates adhesion of sticky materials. | Sticky, high-moisture materials. Secondary or tertiary sliding wear zones. | Deforms under load at temperatures exceeding 80 deg C [176 deg F]. | 1.5x to 2.0x | Mechanical fastening via sheet form. |
| Modified UHMWPE with Solid Lubricant | 0.12 to 0.22 | Abrasion resistance comparable to standard UHMWPE. Incorporates solid lubricants and anti-static additives. | Impact limits match standard UHMWPE. | Lowest friction of the listed liners. Anti-static properties mitigate electrostatic particulate adhesion. | Fine, moist materials and dry powders. | Maximum temperature: 80 deg C [176 deg F]. | 2.5x to 4.0x | Identical to standard UHMWPE. |
| Stainless Steel (304/316 2B finish) | 0.25 to 0.35 | Cold-rolled 2B finish degrades under sliding abrasion. | Moderate impact resistance. | Low initial friction. Friction increases as the finish wears. | Wet materials and corrosive environments. | High corrosion resistance. | 3.0x to 5.0x | Standard fabrication. Requires periodic replacement upon loss of surface finish. |
| Alumina Ceramic Tiles | 0.40 to 0.50 (lower if polished) | High hardness (Mohs 9). High sliding abrasion resistance. | Low impact resistance. Susceptible to fracture under direct loading. | High friction requires steeper hopper wall angles. | High sliding abrasion zones. | High chemical and temperature resistance. | 8.0x to 12.0x | Adhesive bonding or weld studs with ceramic caps. |
| Cast Basalt Tiles | 0.35 to 0.45 | High hardness (Mohs 8). Resists sliding abrasion from fine particulates. | Low impact resistance. Fractures under large particle impact. | Interlocking tile failure occurs if fines penetrate voids. | Downstream sliding abrasion zones. | High chemical resistance. | 5.0x to 7.0x | Requires adhesive bonding. Mechanical fastening is impractical. |
| Chromium Carbide Overlay (CCO) Plate | 0.38 to 0.48 | Overlay hardness 55 to 62 HRC (primary carbides approximately 1,500 HV) on a mild steel backing. | Moderate impact tolerance. | Weld bead striations trap particulates, impeding mass flow and requiring steeper wall angles. | Heavy-duty converging and transition sections. | Robust in standard industrial environments. | 4.0x to 6.0x | Field-weldable. Uses standard fabrication equipment. |
| Quenched and Tempered Abrasion-Resistant Plate | 0.36 to 0.45 | Moderate-to-high hardness (400 to 500 HB). | Through-hardened for high impact resistance. | Functions as a structural wear liner. High friction requires steep wall angles. | Heavy impact and sliding loads on hopper walls, chutes, and skirtboards. | Robust in standard operating environments. | 1.5x to 2.5x | Smooth mill finish. Uses standard machining and forming equipment. |
| Natural Rubber | 0.50 to 0.70 | Low hardness (40 to 60 Shore A). | Provides high impact attenuation. | Unsuitable for mass flow hopper walls. | Primary impact drop zones and noise reduction. | Degrades upon exposure to hydrocarbons, ozone, and sustained temperatures exceeding 70 deg C [158 deg F]. | 2.0x to 3.0x | Mechanical fastening or bonding (typical thickness 40 to 75 mm [1.6 to 3.0 in]). |
| Polyurethane | 0.40 to 0.55 | Moderate abrasion resistance (80 to 95 Shore A). | Moderate impact resilience. | Unsuitable for mass flow hoppers. | Medium-duty impact zones and noise reduction. | Degrades under prolonged ultraviolet (UV) exposure and sustained temperatures exceeding 80 deg C [176 deg F]. | 3.0x to 4.0x | Mechanical fastening or bonding (typical thickness 12 to 25 mm [0.5 to 1.0 in]). |
Note: Friction coefficients are typical values for new liner surfaces. Measure wall friction for the specific bulk solid, moisture content and liner. Relative costs are indicative, indexed to mild steel at 1.0x.
5. Hopper Wall Angles for Mass Flow
Tabulated angles are maximum allowable wall angles for mass flow, measured from vertical, so a smaller angle is a steeper wall. Conical values are cone half-angles and wedge values are the wall inclination of a plane-flow geometry.
| Material | Condition | Liner Type | Conical Hopper Half-Angle deg | Wedge Hopper Wall Angle deg |
|---|---|---|---|---|
| Alumina | Dry powder | Mild steel (unlined) | 20 to 24 | 28 to 32 |
| Alumina | Dry powder | Stainless steel 2B | 24 to 28 | 32 to 36 |
| Alumina | Dry powder | UHMWPE | 28 to 32 | 36 to 40 |
| Alumina | Dry powder | Alumina ceramic | 16 to 20 | 24 to 28 |
| Ash (bottom) | Dry, abrasive | Mild steel (unlined) | 18 to 22 | 26 to 30 |
| Ash (bottom) | Dry, abrasive | Stainless steel 2B | 22 to 26 | 30 to 34 |
| Ash (bottom) | Dry, abrasive | Alumina ceramic | 14 to 18 | 22 to 26 |
| Ash (bottom) | Dry, abrasive | CCO plate | 12 to 16 | 20 to 24 |
| Bauxite | Cohesive | Mild steel (unlined) | 10 to 14 | 18 to 22 |
| Bauxite | Cohesive | Stainless steel 2B | 16 to 20 | 24 to 28 |
| Bauxite | Cohesive | UHMWPE | 22 to 26 | 30 to 34 |
| Bauxite | Cohesive | CCO plate | 8 to 12 | 16 to 20 |
| Biomass (pellets) | Dry | Mild steel (unlined) | 22 to 26 | 30 to 34 |
| Biomass (pellets) | Dry | Stainless steel 2B | 26 to 30 | 34 to 38 |
| Biomass (pellets) | Dry | UHMWPE | 30 to 34 | 38 to 42 |
| Biomass (pellets) | Dry | CCO plate | 18 to 22 | 26 to 30 |
| Carbon black | Powder (cohesive) | Mild steel (unlined) | 8 to 12 | 16 to 20 |
| Carbon black | Powder (cohesive) | Stainless steel 2B | 14 to 18 | 22 to 26 |
| Carbon black | Powder (cohesive) | UHMWPE | 18 to 22 | 26 to 30 |
| Cement | Powder | Mild steel (unlined) | 20 to 24 | 28 to 32 |
| Cement | Powder | Stainless steel 2B | 24 to 28 | 32 to 36 |
| Cement | Powder | UHMWPE | 28 to 32 | 36 to 40 |
| Cement | Powder | CCO plate | 16 to 20 | 24 to 28 |
| Clay-heavy ore/soil | Cohesive | Mild steel (unlined) | 8 to 12 | 16 to 20 |
| Clay-heavy ore/soil | Cohesive | Stainless steel 2B | 14 to 18 | 22 to 26 |
| Clay-heavy ore/soil | Cohesive | UHMWPE | 20 to 24 | 28 to 32 |
| Clay-heavy ore/soil | Cohesive | CCO plate | 6 to 10 | 14 to 18 |
| Clinker | Dry, abrasive | Mild steel (unlined) | 18 to 22 | 26 to 30 |
| Clinker | Dry, abrasive | Stainless steel 2B | 22 to 26 | 30 to 34 |
| Clinker | Dry, abrasive | Alumina ceramic | 14 to 18 | 22 to 26 |
| Clinker | Dry, abrasive | CCO plate | 12 to 16 | 20 to 24 |
| Coal | Dry (less than 8% moisture) | Mild steel (unlined) | 18 to 22 | 26 to 30 |
| Coal | Dry (less than 8% moisture) | Stainless steel 2B | 24 to 28 | 32 to 36 |
| Coal | Dry (less than 8% moisture) | UHMWPE | 28 to 32 | 36 to 40 |
| Coal | Dry (less than 8% moisture) | CCO plate | 14 to 18 | 22 to 26 |
| Coal | Frozen | Mild steel (unlined) | 6 to 10 | 14 to 18 |
| Coal | Frozen | Stainless steel 2B | 12 to 16 | 20 to 24 |
| Coal | Frozen | UHMWPE | 18 to 22 | 26 to 30 |
| Coal | Frozen | CCO plate | 4 to 8 | 12 to 16 |
| Coal | Wet (8% to 15% moisture) | Mild steel (unlined) | 10 to 14 | 18 to 22 |
| Coal | Wet (8% to 15% moisture) | Stainless steel 2B | 16 to 20 | 24 to 28 |
| Coal | Wet (8% to 15% moisture) | UHMWPE | 22 to 26 | 30 to 34 |
| Coal | Wet (8% to 15% moisture) | CCO plate | 8 to 12 | 16 to 20 |
| Coke | Abrasive | Mild steel (unlined) | 16 to 20 | 24 to 28 |
| Coke | Abrasive | Stainless steel 2B | 20 to 24 | 28 to 32 |
| Coke | Abrasive | Alumina ceramic | 12 to 16 | 20 to 24 |
| Coke | Abrasive | CCO plate | 10 to 14 | 18 to 22 |
| Copper ore | Wet (4% to 8% moisture) | Mild steel (unlined) | 12 to 16 | 20 to 24 |
| Copper ore | Wet (4% to 8% moisture) | Stainless steel 2B | 18 to 22 | 26 to 30 |
| Copper ore | Wet (4% to 8% moisture) | UHMWPE | 24 to 28 | 32 to 36 |
| Copper ore | Wet (4% to 8% moisture) | CCO plate | 10 to 14 | 18 to 22 |
| Fertiliser (phosphate) | Hygroscopic | Mild steel (unlined) | 14 to 18 | 22 to 26 |
| Fertiliser (phosphate) | Hygroscopic | Stainless steel 2B | 20 to 24 | 28 to 32 |
| Fertiliser (phosphate) | Hygroscopic | UHMWPE | 26 to 30 | 34 to 38 |
| Fly ash | Dry (150 deg C [302 deg F]) | Mild steel (unlined) | 18 to 22 | 26 to 30 |
| Fly ash | Dry (150 deg C [302 deg F]) | Stainless steel 2B | 22 to 26 | 30 to 34 |
| Fly ash | Dry (150 deg C [302 deg F]) | Alumina ceramic | 14 to 18 | 22 to 26 |
| Fly ash | Dry (150 deg C [302 deg F]) | CCO plate | 12 to 16 | 20 to 24 |
| Grain (wheat/corn) | Dry | Mild steel (unlined) | 24 to 28 | 32 to 36 |
| Grain (wheat/corn) | Dry | Stainless steel 2B | 28 to 32 | 36 to 40 |
| Grain (wheat/corn) | Dry | UHMWPE | 32 to 36 | 40 to 44 |
| Grain (wheat/corn) | Dry | CCO plate | 20 to 24 | 28 to 32 |
| Gravel | Wet | Mild steel (unlined) | 16 to 20 | 24 to 28 |
| Gravel | Wet | Stainless steel 2B | 22 to 26 | 30 to 34 |
| Gravel | Wet | UHMWPE | 26 to 30 | 34 to 38 |
| Gravel | Wet | CCO plate | 14 to 18 | 22 to 26 |
| Gypsum | Synthetic (sticky) | Mild steel (unlined) | 8 to 12 | 16 to 20 |
| Gypsum | Synthetic (sticky) | Stainless steel 2B | 14 to 18 | 22 to 26 |
| Gypsum | Synthetic (sticky) | UHMWPE | 20 to 24 | 28 to 32 |
| Iron ore fines | Wet (6% to 12% moisture) | Mild steel (unlined) | 10 to 14 | 18 to 22 |
| Iron ore fines | Wet (6% to 12% moisture) | Stainless steel 2B | 16 to 20 | 24 to 28 |
| Iron ore fines | Wet (6% to 12% moisture) | UHMWPE | 22 to 26 | 30 to 34 |
| Iron ore fines | Wet (6% to 12% moisture) | Alumina ceramic | 8 to 12 | 16 to 20 |
| Iron ore fines | Wet (6% to 12% moisture) | CCO plate | 6 to 10 | 14 to 18 |
| Limestone (crushed) | Dry | Mild steel (unlined) | 20 to 24 | 28 to 32 |
| Limestone (crushed) | Dry | Stainless steel 2B | 24 to 28 | 32 to 36 |
| Limestone (crushed) | Dry | UHMWPE | 28 to 32 | 36 to 40 |
| Limestone (crushed) | Dry | CCO plate | 16 to 20 | 24 to 28 |
| Nickel ore | Wet, cohesive | Mild steel (unlined) | 10 to 14 | 18 to 22 |
| Nickel ore | Wet, cohesive | Stainless steel 2B | 16 to 20 | 24 to 28 |
| Nickel ore | Wet, cohesive | UHMWPE | 22 to 26 | 30 to 34 |
| Nickel ore | Wet, cohesive | CCO plate | 8 to 12 | 16 to 20 |
| Plastic pellets | Dry | Mild steel (unlined) | 26 to 30 | 34 to 38 |
| Plastic pellets | Dry | Stainless steel 2B | 30 to 34 | 38 to 42 |
| Plastic pellets | Dry | UHMWPE | 34 to 38 | 42 to 46 |
| Potash | Dry | Mild steel (unlined) | 22 to 26 | 30 to 34 |
| Potash | Dry | Stainless steel 2B | 26 to 30 | 34 to 38 |
| Potash | Dry | UHMWPE | 30 to 34 | 38 to 42 |
| Potash | Dry | CCO plate | 18 to 22 | 26 to 30 |
| Salt (rock) | Wet (hygroscopic) | Mild steel (unlined) | 12 to 16 | 20 to 24 |
| Salt (rock) | Wet (hygroscopic) | Stainless steel 2B | 18 to 22 | 26 to 30 |
| Salt (rock) | Wet (hygroscopic) | UHMWPE | 24 to 28 | 32 to 36 |
| Sand (silica) | Wet (3% to 6% moisture) | Mild steel (unlined) | 14 to 18 | 22 to 26 |
| Sand (silica) | Wet (3% to 6% moisture) | Stainless steel 2B | 20 to 24 | 28 to 32 |
| Sand (silica) | Wet (3% to 6% moisture) | UHMWPE | 26 to 30 | 34 to 38 |
| Sand (silica) | Wet (3% to 6% moisture) | CCO plate | 12 to 16 | 20 to 24 |
| Sawdust | Wet (greater than 20% moisture) | Mild steel (unlined) | 10 to 14 | 18 to 22 |
| Sawdust | Wet (greater than 20% moisture) | Stainless steel 2B | 16 to 20 | 24 to 28 |
| Sawdust | Wet (greater than 20% moisture) | UHMWPE | 22 to 26 | 30 to 34 |
| Screened aggregate | Dry | Mild steel (unlined) | 22 to 26 | 30 to 34 |
| Screened aggregate | Dry | Stainless steel 2B | 26 to 30 | 34 to 38 |
| Screened aggregate | Dry | UHMWPE | 30 to 34 | 38 to 42 |
| Screened aggregate | Dry | CCO plate | 18 to 22 | 26 to 30 |
| Soybean meal | Cohesive | Mild steel (unlined) | 12 to 16 | 20 to 24 |
| Soybean meal | Cohesive | Stainless steel 2B | 18 to 22 | 26 to 30 |
| Soybean meal | Cohesive | UHMWPE | 24 to 28 | 32 to 36 |
| Sugar (raw) | Wet, sticky | Mild steel (unlined) | 8 to 12 | 16 to 20 |
| Sugar (raw) | Wet, sticky | Stainless steel 2B | 14 to 18 | 22 to 26 |
| Sugar (raw) | Wet, sticky | UHMWPE | 20 to 24 | 28 to 32 |
| Urea prills | Hygroscopic | Mild steel (unlined) | 16 to 20 | 24 to 28 |
| Urea prills | Hygroscopic | Stainless steel 2B | 22 to 26 | 30 to 34 |
| Urea prills | Hygroscopic | UHMWPE | 26 to 30 | 34 to 38 |
| Wood chips | Wet (greater than 40% moisture) | Mild steel (unlined) | 8 to 12 | 16 to 20 |
| Wood chips | Wet (greater than 40% moisture) | Stainless steel 2B | 14 to 18 | 22 to 26 |
| Wood chips | Wet (greater than 40% moisture) | UHMWPE | 20 to 24 | 28 to 32 |
| Zinc ore | Wet (greater than 6% moisture) | Mild steel (unlined) | 12 to 16 | 20 to 24 |
| Zinc ore | Wet (greater than 6% moisture) | Stainless steel 2B | 18 to 22 | 26 to 30 |
| Zinc ore | Wet (greater than 6% moisture) | UHMWPE | 24 to 28 | 32 to 36 |
| Zinc ore | Wet (greater than 6% moisture) | CCO plate | 10 to 14 | 18 to 22 |
Note: Tabulated values assume new liner surfaces and are guideline values only. Determine design angles from shear cell wall friction tests on the specific material, moisture content and liner surface. Apply a design margin of 3 to 5 degrees steeper than the calculated critical angle, based on the highest wall friction angle measured across the expected moisture range. Wedge values exceed conical values for identical material and liner combinations because the plane-strain stress state permits mass flow at shallower wall angles than the axisymmetric stress state of a cone.
6. Pressure Relief Breaks and Stepped Hopper Geometry
In high-aspect-ratio silos, a continuous converging hopper transmits high vertical consolidating stress to the discharge opening under initial fill (active stress) conditions, and the resulting head load can exceed feeder shear and breakaway torque capacities.
Segment the hopper with vertical expansion zones or stepped inclinations to induce bulk solid dilation, which reduces consolidation strength and the active vertical stress at the feeder interface.
| Configuration | Description | Advantages | Limitations |
|---|---|---|---|
| Compound Angle Hoppers | The upper section of the bin is built at a shallow angle (e.g. 50 degrees from horizontal) to hold high volume. The lower section transitions via a sharp break to a steep angle (e.g. 75 degrees from horizontal) to promote mass flow at the discharge point. | Allows large storage volumes while promoting mass flow at the extraction point. Mitigates arching of cohesive materials (e.g. wet iron ore fines and sticky clays). Requires less headroom than a single mass flow hopper of equal volume. | Increases fabrication complexity. Upper section operates in funnel flow, with stagnant material at the walls. |
| Expansion Steps (Relief Ledges) | The hopper converges, transitions to a short, wider vertical cylinder, and then converges again. The vertical break partially isolates the weight of the upper column of bulk material from the lower column. | Reduces the vertical head load acting on the feeder, reducing motor and gearbox breakaway torque requirements. Mitigates arching of cohesive materials. | Improper design without sufficient slope recovery can create a dead zone that traps tramp material and disrupts the flow profile. Increases fabrication complexity. Requires more vertical headroom. |
| Hopper Inserts (Cone-in-Cone or Inverted Cone) | An inner hopper or stationary inverted cone is suspended inside the main outer hopper, geometrically separating the flow into an inner central channel and an outer annular channel. | Promotes mass flow at shallower outer hopper angles and reduces vertical head loads on feeders. Blends material by forcing it to draw from multiple cross-sectional zones simultaneously. | Introduces internal structural complexity. Requires supports designed for heavy dynamic loads that do not impede flow. Internal components are susceptible to wear and are difficult to access for maintenance. |
| Transition Hoppers (Cone-to-Slot) | A conical upper section transitions to a wedge lower section ending in a slotted outlet aligned with the feeder. | Combines the storage geometry of a circular vessel with a slotted outlet suited to belt and apron feeders. The wedge section permits mass flow at shallower walls than a full cone. | The intersection of conical and planar surfaces concentrates wall pressure and abrasive wear. Fabrication is difficult due to the complex intersecting geometry. |
| Anti-Dynamic Tubes (Standpipes) | A vertical pipe with multiple side openings is installed centrally from the top of the bin down to the discharge outlet, breaking the continuous bulk mass into separate vertical draw points. | Reduces dynamic wall loads and the vertical load on the feeder by drawing material from the top layer downwards. | Requires free-flowing material. Cohesive materials plug the side openings. The internal tube requires heavy structural anchoring to withstand the downward drag forces of the surrounding material. |
7. Dead Bed Protection (Sacrificial Material Cushion)
Maintain a dead bed of material above the discharge opening during normal operation to attenuate impact energy. Direct free-fall onto an empty hopper can fracture wear liners, damage conveyor belts and apron pans, and initiate fatigue cracking.
| Category | Requirement | Rationale |
|---|---|---|
| Bed Specifications | Establish a static material layer typically 1.0 to 2.0 m [3.3 to 6.6 ft] deep, depending on lump size and drop height. Account for reduced live storage capacity in structural and process designs. | The dead bed material distributes impact energy through inter-particle friction and compression, reducing peak point-load forces. |
| Monitoring and Control | Monitor the dead bed level using a low-level sensor (e.g. microwave or nucleonic point-level switch) installed at the minimum elevation. Interlock this sensor to the control system to halt extraction or trigger an alarm at the minimum level. | Halts extraction or raises an alarm before the impact zone is exposed. |
| Commissioning and Maintenance | Re-establish the dead bed before normal operation commences following initial commissioning or maintenance cleanouts. A temporary dead bed of expendable material (e.g. sand or fine gravel) is acceptable, where it is compatible with the downstream process and product specification. | Protects liners and the feeder from the first loads after a cleanout. |
8. Bin Impact Protection Systems
Install replaceable impact-resistant elements on bin structural zones exposed to direct material impact, particularly the impact plate at the load point and the upper hopper walls. These elements limit shell plate deformation and perforation, and provide a sacrificial wear surface replaceable without cutting and re-welding the primary structure.
| Type | Duty Class and Application | Material and Hardness | Lump Size and Drop Height | Mounting Method | Advantages | Limitations |
|---|---|---|---|---|---|---|
| Chromium Carbide Overlay (CCO) Plate | Medium duty sliding abrasion and moderate direct impact applications (e.g. secondary crushed ore). | 10 to 12 mm [3/8 to 1/2 in] mild steel backing plate with a 5 to 8 mm [3/16 to 5/16 in] hard-faced weld deposit. Overlay macro-hardness 55 to 62 HRC. | Lump sizes of 100 to 300 mm [4 to 12 in]. Drop heights of 3 to 8 m [10 to 26 ft]. | Panels are bolted or plug-welded directly. | Effective against sliding abrasion. | Brittle overlay is susceptible to cracking and spalling under high point loads. Replacement of plug-welded panels requires hot work including cutting, grinding and welding. |
| Cast White Iron Tiles | Medium duty alternative to CCO plate for secondary crushed ore and screened aggregate. | High-chromium cast white iron, typically 600 to 700 HB. | Lump sizes of 100 to 300 mm [4 to 12 in]. Drop heights of 3 to 8 m [10 to 26 ft]. | Tiles are bolted, or welded through a mild steel backing or stud. | High sliding abrasion resistance. | High hardness induces brittleness. Susceptible to fracture and spalling under high-energy point loads. Unsuitable for primary direct impact zones. |
| Railway Rail Steel | Heavy duty primary direct free-fall impact zones (e.g. ROM ore). | Head-hardened rail sections. Hardness of 340 to 390 HB. | Lump sizes greater than 300 mm [12 in]. Drop heights greater than 5 m [16 ft]. | Rails mounted on saddle brackets with countersunk bolts at 600 mm [24 in] centres. Limit inter-rail gaps to 10 to 15 mm [3/8 to 5/8 in]. Tie adjacent rails with flat bar welded to the rail foot at 500 to 600 mm [20 to 24 in] intervals. Do not weld to the hardened head. | Rounded head geometry deflects incoming mass and reduces normal stress transfer to the substrate. | Wider inter-rail gaps allow material packing. Exhibits accelerated wear under continuous sliding abrasion. |
| Rubber Impact Cushions | Light duty applications involving low-abrasion bulk solids (e.g. coal, grain, fertiliser). | 50 to 75 mm [2 to 3 in] vulcanised rubber panels. Hardness of 60 to 70 Shore A durometer. | Lump sizes less than 100 mm [4 in]. Drop heights less than 3 m [10 ft]. | Panels are bolted directly. | Provides protection for low-abrasion bulk solids. | Unsuitable for ROM ore, heavy mineral sands, sharp material geometries or drop heights greater than 3 m [10 ft]. |
| UHMWPE Block Liners | Specified for light duty sliding applications (e.g. coal, grain, fertiliser). | UHMWPE. | Lump sizes less than 100 mm [4 in]. Drop heights less than 3 m [10 ft]. | Panels are bolted directly with countersunk fasteners. | Offers a low-friction wear surface. | Unsuitable for temperatures exceeding 80 deg C [176 deg F]. Low shear strength renders the polymer susceptible to deep gouging and accelerated material loss from sharp or high-mass particles. |
| Hybrid Lining System | Specified for transition zones exhibiting simultaneous direct impact and sliding abrasion vectors (e.g. vertical drop zone entering an angled chute). | Railway rail steel and CCO plate combination. | Lump sizes greater than 300 mm [12 in]. Drop heights greater than 5 m [16 ft] transitioning to sliding zones. | Railway rail steel in the primary direct impact zone transitioning to CCO plate in the downstream sliding zone. | Matches liner properties to localised load conditions. | Requires separate installation methods for each liner type. |
9. Hopper and Discharge Geometry
9.1 Upper Hopper Geometry
The upper hopper geometry governs gravity flow. Correct geometry reduces bridging, ratholing and material hang-up.
| Geometry Feature | Specification | Description | Purpose |
|---|---|---|---|
| Surcharge Volume | Accommodate the peak surge volume (e.g. one haul truck payload, or the inflow in excess of feeder rate over the surge duration). | Vertical clearance and volumetric space above the active hopper section. | Absorbs transient feed surges. Reduces material overspill. |
| Inlet Grizzly Screen | Set aperture spacing less than one third of the minimum hopper outlet dimension. | Heavy grid structure positioned across the hopper top opening. | Restricts oversized particles. Limits mechanical arching and outlet blockages. |
| Impact Baffle | Positioned to intersect the material free fall trajectory. | Deflector plate or dead bed rock box located below the feed point. | Absorbs kinetic energy. Prevents direct impact on hopper walls and the feeder. |
| Hopper Wall Angle | Set from wall friction testing. Typically 60 to 75 degrees from horizontal for conical hoppers. | Incline angle of the converging hopper walls. | Achieves mass flow, avoiding funnel flow, stagnant material and ratholing. |
| Minimum Outlet Width | Greater than the critical arching dimension from flow property testing. | Smallest horizontal span of the hopper discharge opening. | Prevents cohesive arching across the outlet. |
| Valley Angles | Set the valley angle to the conical mass flow limit. For a square pyramid with walls 55 to 75 degrees from horizontal, the walls are 6 to 10 degrees steeper than the valley. | Angle formed at the internal intersection of two converging rectangular or square walls. | Reduces material hang-up. Valleys are shallower than the adjacent walls. |
| Hopper Shape Configuration | Specify wedge or trough shapes in preference to conical or pyramidal for cohesive materials. | Three-dimensional geometry of the converging section. | Wedge hoppers achieve mass flow at wall angles 8 to 12 degrees shallower than conical hoppers. The critical arching width of a slot outlet is approximately half the critical diameter of a circular outlet. |
| Bin to Hopper Transition | Flush joints with ground welds. No internal ledge permitted. | Joint where vertical bin walls meet the converging hopper walls. | Eliminates structural ledges where material can compact and form anchor points for bridging. |
| Internal Surface Finish and Liners | Select from wall friction and wear testing. Low-friction options are UHMWPE and polished stainless steel. Countersink fasteners flush with the liner surface. | Internal wear lining applied to the converging hopper walls. | Lowers wall friction to promote flow. Reduces the required hopper wall angle and protects against abrasion. |
9.2 Lower Hopper Geometry
The lower feeder hopper geometry controls the discharge. Correct geometry lets material decompress, shear smoothly and transition onto the feeder and to the next stage without spillage or belt damage.
| Geometry Feature | Specification | Description | Purpose |
|---|---|---|---|
| Hopper Opening Taper | 25 to 50 mm/m [0.3 to 0.6 in/ft] of length. | Width increases in the direction of belt travel. | Facilitates material shear and decompression. Mitigates particle wedging. Lowers shear friction and reduces drive power. |
| Vertical Clearance | Increases from 25 mm [1 in] at the rear to 50 mm [2 in] at the front. | Space between the hopper bottom edge and the moving belt. Do not set parallel to the belt. | Reduces wedging of entrained particles, drag and belt cover damage. |
| Vertical Relief | Downward expanding taper in the vertical plane. 1 to 3 degree draft angle. | Gradual outward expansion of the vertical throat channel geometry. | Reduces lateral wall pressure and the risk of mechanical bridging at the primary shear point. |
| Throat Length | 300 to 1,000 mm [12 to 40 in]. | Region immediately downstream of the hopper trailing edge. | Acts as a wear and flow control zone until material is supported without hopper confinement. |
| Trailing Edge Discharge Lip | 10 to 20 mm [3/8 to 3/4 in] radius. | Radiused steel lip on the downstream edge. Do not use a square edge. | Reduces belt gouging and lump jamming at the edge. |
| Isolation Gate | Retractable closure mechanism. Open area greater than or equal to the hopper outlet cross-section. | Pin gate or slide gate positioned immediately above the feeder interface. | Enables maintenance isolation. Fully retracts outside the material flow path to prevent flow restriction. |
| Outlet Cheek Plates | Flush mounted wear liners. No inward ledge permitted. | Sacrificial plates installed on the internal faces of the outlet throat. | Protects structural steel from abrasive wear. Maintains continuous material shear without creating anchor points. |
| Strike-Off Plate | Vertically adjustable. Lower edge is parallel to the belt. | Vertical plate located at the downstream exit of the hopper outlet. | Controls the volumetric profile of the material discharging onto the feeder belt. |
| Skirtboard Extension | Minimum 1.5 times the hopper opening length. | Confinement walls extending along the belt beyond the trailing edge. | Prevents the material bed from spreading laterally before it has decompressed and stabilised. |
| Skirtboard Gap | 3 to 6 mm [1/8 to 1/4 in]. | Clearance between the bottom of the skirtboards and the moving belt. | Limits fines leakage under lateral bed pressure while material is in the throat zone. |
10. Active Bulk Flow Aids
Even with correct mass flow geometry and low-friction liners, cohesive materials (e.g. wet clays, bauxite or frozen coal) may still bridge or rathole due to fluctuating moisture content or prolonged storage. When passive geometric design is insufficient, install active flow aids to break blockages and restore material flow into the feeder shear plane.
| Flow Aid System | Target Material and Application | Mechanics | Placement Geometry and Installation | Timing and Operational Rules | Primary Hazards and Risks |
|---|---|---|---|---|---|
| Air Cannons (Air Blasters) | High bulk density particulates prone to structural arching and mechanical interlocking. | Uses a pressure vessel discharging through a quick-release valve to break cohesive bonds and collapse material arches. | Mount nozzles aiming downward parallel to hopper walls at the elevation where the hopper width approximates the critical arching dimension. For ratholing, position cannons higher in the vessel and fire tangentially. | Fire in a staggered sequence from the bottom up to break the arch base. Simultaneous firing of the lowest tier is applicable for ratholing geometries. Fire only with the feeder running. | Incorrect sequencing causes compaction. Firing the top tier first acts as a pneumatic hammer. This drives upper material down and compacts the arch below it. Isolate and depressurise cannons before vessel entry or nozzle maintenance. |
| Industrial Vibrators and Bin Activators | Fine particulates and cohesive powders prone to ratholing and boundary wall adhesion. | Applies high-frequency mechanical vibration to reduce inter-particle and wall friction and break wall adhesion. | Mount vibrators on a stiffened mounting channel welded to the hopper wall, typically in the lower third of the hopper. Activators are suspended from the main bin on rubber isolation seals. | Do not energise unless the feeder is running and the discharge gate is fully open to provide an open flow path. | Running against a closed gate or stopped feeder compacts the material into a consolidated mass. Fatigue cracking of the hopper wall at unstiffened mounts. |
11. Feeder Belt Selection
Belt feeder selection is governed by tension and load support, not speed. The controlling load case is breakaway under an initially filled hopper, where shear resistance across the outlet aperture dominates.
11.1 Selection Inputs
Establish the inputs below before nominating any belt construction.
| Input | Data Required | Selection Consequence |
|---|---|---|
| Material characterisation | Bulk density, particle size distribution, top size, moisture, angle of internal friction, wall friction angle | Sets hopper drag, impact energy, cover grade |
| Top size and lump shape | d95 and maximum lump, angularity | Sets top cover thickness, breaker ply, cover grade |
| Abrasiveness | Los Angeles or Cerchar index, silica content | Sets cover grade and cover thickness for target life |
| Hopper geometry | Outlet length and width, taper in plan and elevation, skirt divergence | Governs shear plane drag and belt tension |
| Feeder geometry | Centres, belt width, incline, idler pitch or slider bed extent | Governs sag, load support, belt mass |
| Speed | Design and turndown range, commonly 0.05 to 0.50 m/s [10 to 100 fpm] | Low speed reduces speed-related wear but raises tension per unit capacity |
| Drive arrangement | Motor rating, starting method, breakaway torque limit, reversing duty | Sets T1 and T2 and therefore belt rating |
| Duty cycle | Starts per hour, run hours, plugged-chute restart cases | Sets fatigue allowance on splice and carcass |
| Environment | Ambient and material temperature, oil, chemicals, underground classification | Sets cover polymer and statutory compliance |
11.2 Carcass and Ply Count
Belt ply count is set by the greater of the tensile requirement and the load-support requirement. Two-ply constructions satisfy many rating requirements but are not suited to feeder duty, because carcass thickness governs transverse load support and impact distribution.
| Duty | Minimum Plies | Basis |
|---|---|---|
| Fine or screened product feeder | 3 | Load support and fastener holding |
| ROM feeder, top size to 300 mm [12 in] | 4 | Impact distribution and transverse stiffness |
| Primary ROM feeder, top size greater than 300 mm [12 in] | 4 to 5 | Impact, rip resistance, static column support |
| Reclaim feeder under a deep stockpile or bin | 5 | Sustained normal load and edge shear |
Specify sufficient transverse stiffness to maintain contact with the skirtboard seals along the full hopper length. A belt with inadequate transverse stiffness dishes between idlers, opening gaps at the skirtboard interface and allowing fines to escape under lateral bed pressure. Steel cord feeder belts have lower transverse rigidity than multi-ply fabric belts of equivalent strength. For steel cord belts, specify spring-loaded or gravity-adjusted seal strips rather than fixed-gap seals.
11.3 Top Cover
Belt top cover is a wear allowance plus an impact-absorption layer. Size it from a measured or benchmarked wear rate and the target replacement interval, then check that not less than 1.5 mm [0.06 in] of cover remains above the breaker or carcass at end of life. Do not exceed a top-to-bottom cover ratio of approximately 3:1 on fabric belts. Higher ratios promote cupping and edge lift once the belt takes a set.
Specify abrasion-resistant cover grades as a minimum. Use AS 1332 grade N / ISO 14890 L / DIN 22102 grade Y for normal duty, and AS 1332 grade M / ISO 14890 H / DIN 22102 grade X for cutting, gouging and impact from large lumps. Use ISO 14890 D / DIN 22102 grade W where sliding abrasion governs.
| Duty | Top Cover mm [in] | Notes |
|---|---|---|
| Screened product, low abrasion | 6 to 8 [0.24 to 0.31] | Wear-governed |
| ROM coal, top size to 300 mm [12 in] | 8 to 12 [0.31 to 0.47] | Breaker ply required |
| ROM hard rock, top size to 600 mm [24 in] | 12 to 16 [0.47 to 0.63] | Breaker ply required |
| Primary crusher discharge or apron replacement duty | 16 to 25 [0.63 to 1.0] | Verify pulley diameter and splice length |
11.4 Bottom Cover
Bottom cover thickness is set by the belt support type. The values below are starting thicknesses for tender enquiry. Check the resulting selection against the top-to-bottom cover ratio limit of approximately 3:1.
| Belt Support Type | Bottom Cover mm [in] | Notes |
|---|---|---|
| Impact idlers or rollers | 3 to 5 [0.12 to 0.20] | Minimum 3 mm [0.12 in] on any feeder |
| Slider bed, UHMWPE or steel | 5 to 8 [0.20 to 0.31] | Specify an abrasion-resistant compound. Verify the friction coefficient against the bed material. |
Note: Top covers greater than 15 mm [0.6 in] on idler-supported feeders require a bottom cover above the tabulated range to hold the 3:1 ratio.
11.5 Breaker Ply
A breaker ply distributes point impact, limits cover penetration, resists longitudinal ripping and improves mechanical fastener retention. It does not contribute to the belt tensile rating and is not counted in the ply designation. Rip protection is not a substitute for tramp metal detection and removal in the materials handling circuit.
| Parameter | Guidance |
|---|---|
| When to specify | Top size greater than approximately 150 mm [6 in], angular or sharp material, drop height greater than approximately 1.0 m [3.3 ft], any tramp metal exposure |
| Fabric | Nylon or polyester open-weave, typically 150 to 400 g/m2 [0.031 to 0.082 lb/ft2] |
| Position | Embedded in the top cover with not less than 3 mm [0.12 in] of cover above it |
| Quantity | One ply is standard. Two plies where tramp metal risk is sustained. |
| Enhanced protection | Aramid ripstop grid, or a transverse cord layer, where longitudinal rip cost dominates |
| Trade-off | Adds carcass stiffness. Not a constraint on a flat feeder, but check minimum pulley diameter. |
12. Feeder Belt Tension and Drive Power
Feeder drive sizing is governed by two load cases. The initial fill case sets breakaway torque, while the flow case sets continuous running duty.
Under initial fill, material charged into an empty hopper above a stationary feeder develops an active stress field and high vertical stress at the shear plane. Once discharge commences, the stress field converts to a passive arched state in which the hopper walls carry a greater share of the material weight, and the vertical load at the outlet falls substantially. Initial fill loads are typically 2 to 4 times established flow loads.
Time consolidation during extended shutdowns increases shear strength at the shear plane, and refilling over a stopped feeder restores the initial fill stress field. Retain breakaway capacity for the life of the installation, not only for first fill.
Compute the vertical shear plane force from measured flow properties using the Jenike or Roberts methods. Select the gearbox against peak breakaway torque with a service factor of 1.5 to 2.0 for feeder duty, and verify the motor, coupling and holdback ratings against the same torque, not against nameplate power.
| Component | Basis of Calculation | Typical Values |
|---|---|---|
| Hopper drag | Equivalent friction coefficient multiplied by the vertical force on the shear plane (mean vertical pressure multiplied by outlet length and width), from Jenike or Roberts analysis of measured flow properties. | 60% to 80% of total effective tension. |
| Skirtboard friction | Lateral force per unit length on each skirt wall (pressure ratio multiplied by bulk density, gravity and the square of bed depth, divided by 2), multiplied by skirt length, two walls and the wall friction coefficient, plus seal contact drag. | Second largest component on long throat and skirt extensions. |
| Belt and support friction | Idler support: friction factor of 0.03 to 0.05 applied to the weight of belt plus material. Slider bed: friction coefficient of 0.20 to 0.35 (rubber cover on UHMWPE) applied to the supported weight. Verify slider friction against the specific cover compound and bed material. | Slider beds increase this component 4 to 12 times over idlers. |
| Grade resistance | Material mass per unit length multiplied by gravitational acceleration and lift height on inclined feeders. Belt weight cancels between carry and return strands. | Zero on horizontal feeders. |
| Acceleration | Total moving mass multiplied by ramp acceleration. | Negligible at typical Variable Frequency Drive (VFD) ramp rates. Verify for short-ramp restart cases. |
| Accessories | Belt cleaner and plough drag per manufacturer data. | Minor. |