1. Transfer Points, Belt Cleaning, and Skirting
Conveyor belt damage, dust generation, and spillage originate primarily at transfer points through impact and abrasion. Improper skirting and inadequate load support damage the belt top cover, and ineffective belt cleaners permit carryback, which damages return idlers and causes mistracking.
2. Transfer Chute Design and Material Trajectory
Transfer chute design dictates top cover wear, dust generation, material degradation, and flow continuity. Centre-load bulk material at a velocity and direction matching the receiving belt.
2.1 Material Trajectory Calculations
Discharged bulk material follows an approximately parabolic trajectory governed by gravity, belt speed, pulley radius and material bed depth. If the impact wall is too close to the head pulley, material ricochets backward onto the belt cleaners. If it is too far, material misses the wear liners and wears the unlined chute wall.
| Method | Calculation Details | Advantages | Limitations |
|---|---|---|---|
| Conveyor Equipment Manufacturers Association (CEMA) Analytical Method | Treats the material stream as a rigid body rotating with the pulley. Calculates the centroid radius, R_c, centroid velocity, v_c, and separation angle, theta, then plots the free-fall path from the separation point using the formulas below. | Common practice for moderate-speed dry materials. | Assumes rigid-body behaviour. Overestimates trajectory range at high belt speed. Ignores air resistance and post-impact flow. |
| Mechanical Handling Engineers' Association (MHEA) / Booth | Uses the belt speed, v_b, in place of the centroid velocity, v_c, to plot the trajectory. The Korzen method adds an air-drag deceleration term derived from bulk density and equivalent particle diameter. | Reduces trajectory overestimation at high belt speed. The Korzen method accounts for aerodynamic drag. | Limited to theoretical 2D curves. Relies on generalised drag coefficients. Ignores post-impact flow dynamics. |
| Discrete Element Method (DEM) | Computational simulation that assigns properties to discrete particles and solves Newton's laws of motion for position, collision and gravity interactions. | Models 3D flow, wear zones and blockages. Accommodates cohesive and variable materials. | Requires specialised software, significant computational resources and laboratory calibration of material parameters. Accuracy depends on that calibration. |
v_c = v_b * R_c / (R_p + t_b)
Where:
- v_c = Velocity of the material cross-section centroid at discharge (m/s)
- v_b = Belt speed (m/s)
- R_c = Centroid radius, equal to R_p + t_b + h_c (m)
- R_p = Pulley radius, including lagging (m)
- t_b = Belt thickness (m)
- h_c = Height of the material cross-section centroid above the belt surface (m)
Engineering Takeaway: The rigid-rotation assumption gives the centroid a higher speed than the belt. Deep beds on small pulleys therefore produce the longest predicted trajectories.
COS(theta) = v_c^2 / (g * R_c)
Where:
- theta = Separation angle, measured from the vertical through the pulley centre (deg)
- v_c = Material centroid velocity (m/s)
- g = Gravitational acceleration, 9.81 (m/s2)
- R_c = Centroid radius (m)
Note: Where v_c^2 / (g * R_c) is greater than or equal to 1, material separates at the tangent point, and theta = 0 deg for a horizontal belt. On an inclined belt, material separates at the tangent point where the belt inclination is greater than or equal to theta.
Engineering Takeaway: Low belt speed on a large pulley carries material over the pulley before separation, which steepens the discharge and shortens the trajectory.
X = v_c * t * COS(theta)
Y = v_c * t * SIN(theta) + 0.5 * g * t^2
Where:
- X = Horizontal distance from the separation point (m)
- Y = Vertical drop below the separation point (m)
- v_c = Material centroid velocity (m/s)
- t = Time after separation (s)
- theta = Separation angle (deg), negative for an upward launch from the tangent point of an inclined belt
- g = Gravitational acceleration, 9.81 (m/s2)
Note: The MHEA and Booth methods substitute the belt speed, v_b, for v_c.
Engineering Takeaway: Plot the trajectory at minimum and maximum design throughput, since bed depth changes the centroid radius and velocity. Position the hood or impact plate so it intercepts the full stream envelope within the lined zone.
2.2 Curved and Lobster-Back Chute Comparison
The two primary chute fabrication methods are true curved (rolled plate) and lobster-back (faceted flat plate). Both maintain continuous material flow but differ in fabrication and maintenance cost.
| Feature | True Curved (Rolled Plate) Chutes | Lobster-Back (Faceted) Chutes |
|---|---|---|
| Design and Geometry | Continuous curved profile intercepts the material stream. | Approximates a curved profile with flat steel plates welded at shallow, intersecting angles. |
| Material Flow Dynamics | Material retains kinetic energy and the stream remains consolidated through the transfer. | Performance approaches a true curve, depending on facet count, facet angles and belt speed. |
| Conveyor Performance | Aligns material velocity with the receiving belt, reducing cover wear and drive power. | Similar benefit where facet angles are optimised. |
| Dust Generation | Reduces air entrainment and dust generation. | Reduces dust, limited by the transition between facets. |
| Fabrication Complexity | Requires heavy plate-rolling equipment and specialised fabrication to roll thick, high-hardness plate into three-dimensional curves. | Fabricated from flat plate by most fabricators, without plate-rolling equipment. |
| Capital Cost | Higher, due to specialised fabrication. | Lower. |
| Maintenance | Requires custom-rolled replacement liners at higher cost. | Uses standard bolted flat wear tiles. |
2.3 Discrete Element Method Simulation
Analytical 2D trajectory models have limited accuracy for high-speed chute design because bulk material behaves as discrete interacting particles. DEM uses 3D computational models of particle kinematics, including gravity, wall friction, restitution and moisture cohesion.
Use DEM analysis for the following:
- Wear Prediction: Generates wear maps of peak impact and sliding abrasion to guide liner selection and placement.
- Volumetric Capacity Verification: Confirms the chute geometry passes the maximum volumetric surge without bridging or blockage.
- Velocity Alignment: Sets internal deflector angles to align the exit velocity vector with the receiving belt, reducing cover wear and material turbulence.
- Centreline Loading: Confirms symmetrical material distribution on the receiving belt, reducing mistracking and spillage.
- Flow Continuity: Identifies deceleration zones where material pools. Correcting the wall angles maintains forward momentum and reduces abrasive wear on the receiving belt.
2.4 Chute Wear Liner Selection and Materials
Line transfer chute structural steel with sacrificial wear liners. Liner selection governs service life, and incorrect selection results in impact fracture, accelerated abrasive wear or material bridging.
| Material | Composition and Design | Impact Resistance | Sliding Abrasion Resistance | Material Flow and Friction | Fabrication and Installation | Application |
|---|---|---|---|---|---|---|
| Abrasion-Resistant (AR) Steel | Through-hardened, quenched and tempered steel plate, typically 400 to 500 HB. | High toughness. Withstands perpendicular impact from run-of-mine (ROM) material. | Limited service life under sliding abrasion from high-silica materials. | High friction coefficient. Susceptible to material bridging with cohesive ores. | Low-cost baseline. Suitable for in-situ cutting and welding. | Baseline liner for primary impact zones with moderate sliding abrasion. |
| Chromium Carbide Overlay (CCO) | Mild steel backing plate clad with chromium carbide weld overlay. | Brittle overlay susceptible to spalling under perpendicular impact. | Higher sliding abrasion resistance than AR steel. | Polishes under continuous material flow, reducing the friction coefficient. | Difficult to form into complex or tight-radius geometries. | Straight sliding zones with high abrasion and low perpendicular impact. |
| Alumina Ceramic Tiles | Alumina tiles, typically 92% to 95% Al2O3. | Brittle. Susceptible to fracture under perpendicular impact unless vulcanised into an elastomeric matrix. | High sliding abrasion resistance in high-velocity, high-silica applications. | Higher surface friction than polished steel, requiring steeper wall angles. | Epoxy-bonded or mechanically fastened. | High-velocity sliding zones with minimal direct impact. |
| Impact Bars (Baffle Panels) | Shock-absorbing elastomeric bars or panels. | Absorbs kinetic energy, reducing structural fatigue and material degradation. | Low sliding abrasion resistance. Elastomer wears under continuous sliding contact. | High friction coefficient. Unsuitable for sliding zones. | Mechanically fastened to the structural backing. | Sacrificial shock absorption in primary perpendicular impact zones. |
| Mild Steel | Low-carbon structural steel (e.g. AS/NZS 3678 Grade 250 / ASTM A36). | Ductile. Subject to plastic deformation rather than fracture. | Low sliding abrasion resistance. | Corrosion increases friction and material bridging. | Low cost. Easily fabricated and welded. | Structural backing or non-wear zones. |
| Stainless Steel | Austenitic chromium-nickel stainless steel (e.g. 304 or 316). | Ductile. Deforms plastically under heavy impact. | Moderate abrasion resistance. Work-hardening grades extend service life. | Low-friction surface. Resists corrosion and material adhesion. | Requires specialised welding consumables and heat input control. | Cohesive or corrosive material handling where flow continuity is critical. |
| Engineering Plastics | Ultra-high molecular weight polyethylene (UHMWPE) or polyurethane (PU). | Elastic properties absorb light impact. Susceptible to gouging from sharp bulk materials. | Resists fine-particle sliding abrasion. Unsuitable for coarse rock sliding. | UHMWPE has a low friction coefficient that reduces bridging and ratholing. PU has a higher friction coefficient. | Mechanically fastened. Requires allowance for thermal expansion. Cannot be welded. | Fine or cohesive material sliding zones prioritising flow over wear resistance. |
| Rubber Liners (Elastomers) | Vulcanised natural or synthetic elastomers, often steel-reinforced. | High elastic deformation. Absorbs kinetic energy without permanent yield. | Resistant to fine wet slurry abrasion. Susceptible to gouging from dry, sharp rock. | High friction coefficient. Unsuitable for dry sliding zones. | Mechanically fastened or cold-vulcanised. | Primary impact zones or wet slurry handling requiring kinetic energy absorption. |
| High-Density Polyethylene (HDPE) | Thermoplastic polymer with shorter chains than UHMWPE. | Moderate impact resistance. Prone to brittle fracture at low temperatures. | Lower abrasion resistance than UHMWPE or PU. | Low friction coefficient. Resists moisture absorption. | Easily machined and plastic-welded. Mechanically fastened. | Low-cost liner for light-duty, low-abrasion flow promotion. |
| Polytetrafluoroethylene (PTFE) | Synthetic fluoropolymer. | Low yield strength. Deforms under direct impact. | Low mechanical wear resistance. | Lower friction coefficient than UHMWPE. High resistance to material adhesion. | Mechanically clamped or bonded to rigid backing. | Flow promotion at constrictions handling cohesive materials. |
| Cast Nylon (Polyamide) | Semi-crystalline engineering thermoplastic. | High structural rigidity. Lacks elastomeric energy absorption. | High dry sliding abrasion resistance under high-pressure loads. | Low friction coefficient. Absorbs moisture and swells. | Machinable. Installed with countersunk fasteners. | Abrasive flow zones operating up to 100 deg C [212 deg F] or high-load friction areas. |
| Aramid-Reinforced Plastics | Polymer resins reinforced with synthetic aramid fibres. | High puncture resistance limits penetration of the base polymer. | High resistance to gouging and deep sliding abrasion. | Fibre exposure during wear increases surface friction. | Supplied as pre-moulded panels requiring mechanical fastening. | High-throughput zones requiring flow promotion and gouging resistance. |
2.5 Transfer Chute Configurations
Where structural layout cannot reduce drop heights sufficiently, select a configuration from the table below to control impact velocity and attrition.
| Chute Type | Operating Principle | Material Suitability | Primary Advantages | Primary Disadvantages | Belt and Energy Impact |
|---|---|---|---|---|---|
| Cascade (Stepped) Chutes | Stepped geometry dissipates kinetic energy through sequential short drops. | Free-flowing, low-moisture friable materials requiring impact mitigation. | Reduces material degradation by limiting impact velocity. Maintains flow continuity. | Perpendicular impact concentrates liner wear on the steps. Requires substantial vertical clearance. | Reduces exit velocity but does not align the stream with the receiving belt. |
| Rock Boxes (Dead-Box Design) | Horizontal ledges retain bulk material, forming a stationary cushion. Subsequent material impacts the retained volume rather than structural components. | Abrasive, non-cohesive bulk materials where wear reduction takes priority over exit velocity. | Impact and sliding act on retained material, extending structural service life and reducing liner cost. | Retained volume disrupts flow continuity, and cohesive material builds up and bridges. The stream loses most of its forward velocity. | Material discharges at near-zero forward velocity, increasing cover wear from slip during re-acceleration and the drive torque required to accelerate the load. |
| Soft-Loading Spoon Configuration | Profiled discharge spoon aligns the material exit speed and direction with the receiving belt. | High-velocity, high-tonnage applications prioritising dust control and belt life. | Reduces uncontrolled rolling and sliding contact, reducing material attrition and extending belt service life. | Requires complex engineering, tight fabrication tolerances and precise installation alignment. | Reduces abrasive cover wear and kinetic energy loss, reducing required drive power. |
| Hood and Spoon (Curved Chutes) | Curved hood intercepts head pulley discharge, maintaining stream consolidation. The enclosed curved profile guides material to a discharge spoon for aligned placement. | Variable bulk materials, including cohesive ores, requiring continuous flow consolidation. | Reduces dust generation by maintaining stream density. Reduces flow disruption and spillage. | High capital cost. Geometry is typically optimised with DEM. | Soft-loads the receiving belt in the direction of travel, reducing cover wear and preserving momentum to reduce drive power. |
| Spiral Chutes | Continuous helical path controls descent velocity through a balance of centrifugal force, gravity and sliding friction. | Friable materials requiring large vertical drops with low degradation. | Controls descent velocity independent of total drop height, reducing attrition and dust generation. | Susceptible to blockages from moisture-induced cohesion. Requires a large installation footprint. | Discharges with low vertical impact force. Requires a transition deflector to align the vector with the receiving belt. |
| Conventional Drop Chutes | Enclosed structure using gravity and flat deflector plates without trajectory control. | Robust materials in short-drop applications without stringent degradation or dust constraints. | Low capital expenditure, simple engineering and easily replaceable flat liners. | Uncontrolled impact increases material attrition, dust generation and liner wear. | High vertical impact forces and turbulence require heavy-duty impact idlers and increased drive torque. |
3. Material Degradation and Attrition
Friable bulk materials (e.g. coal, calcined coke, chemical granules, sintered ore and agricultural pellets) degrade during transfer, and the fines generated by high-velocity impact reduce product yield, increase dust generation and degrade downstream process efficiency. Degradation correlates directly with particle impact velocity at the chute wall or receiving belt, which is governed by discharge velocity and vertical drop height.
Published indices (e.g. the Hardgrove Grindability Index or the brittleness test friability value) indicate material susceptibility to degradation. Establish the permissible drop height by site-specific drop testing of product samples. In the absence of test data, typical maximum drop heights are:
- Friable coal: 1.0 to 1.5 m [3.3 to 4.9 ft]
- Calcined coke or carbon products: 0.5 to 1.0 m [1.6 to 3.3 ft]
- Pelletised agricultural or chemical products: 0.3 to 0.8 m [1.0 to 2.6 ft]
- Sintered ore: 1.0 to 2.0 m [3.3 to 6.6 ft]
4. Skirting and Load Containment
4.1 Skirtboard Length and Geometry
Set the minimum skirtboard length to 1.2 m per 1.0 m/s [2 ft per 100 fpm] of belt speed, plus 0.9 m [3 ft]. Increase the speed term to 1.8 m per 1.0 m/s [3 ft per 100 fpm] where airflow through the transfer exceeds 0.5 m3/s [1,000 ft3/min], or for aerated or near-spherical bulk solids.
Set the clear distance between steel skirtboards to typically two-thirds of the belt width.
Diverge the skirtboards in the direction of belt travel to reduce material wedging, with a lateral taper of 10 to 15 mm per metre [1/8 to 3/16 in per ft] of skirtboard length.
4.2 Internal Wear Liners
Wear liners (e.g. AR steel, ceramic or CCO) resist bulk material pressure and isolate the external skirt seals from abrasion.
Keep the bottom edge of the wear liner clear of the belt, with a diverging gap of 10 mm [3/8 in] at the tail end, increasing to 19 mm [3/4 in] at the exit end, to release entrapped material.
Set the internal face vertical or angled outward. An inward-angled liner creates a continuous pinch point that traps bulk material and causes localised belt cover wear.
Support the skirted zone with continuous impact beds or close-pitch impact idlers to maintain the liner clearances and reduce material entrapment.
| Load Support Configuration | Primary Application | Sag Mitigation Mechanism | Engineering Considerations |
|---|---|---|---|
| Impact Beds (UHMWPE Slider Bars) | High-impact loading zones and fine particulate containment. | Continuous rigid support reduces dynamic belt sag. | Maintains the 10 to 19 mm [3/8 to 3/4 in] wear liner clearance. Increases parasitic drag. |
| Close-Pitch Impact Idlers | Medium-duty loading of coarse bulk solids or systems prioritising low parasitic drag. | Reduces dynamic belt sag through reduced idler spacing, typically 300 mm [12 in]. | Lacks a continuous rigid surface. Inadequate for fine particulate containment. |
4.3 Skirt Seals
Specify a seal that wears before the belt top cover. A seal softer than the cover, typically 45 to 55 Shore A, achieves this. A seal compound with a lower elastic modulus than the cover also achieves it at higher hardness.
Do not use scrapped conveyor belting for skirting. Exposed fabric plies trap abrasive particles, causing longitudinal belt cover wear.
For high-dust applications, specify a dual-lip seal. The primary lip contains bulk material, while the secondary lip lies flat on the belt edge to capture particulate emissions.
| Configuration | Application | Advantages | Limitations and Engineering Considerations |
|---|---|---|---|
| Unlined Steel Skirtboard (No Rubber Seal) | Coarse, non-aerated bulk solids. Low-dust environments. | Low capital expenditure. No seal maintenance. | Poor containment. Requires a large static belt clearance to avoid cover damage. Concentrates steel wear at the belt line. |
| Steel Skirtboard + External Rubber Seal (Unlined) | Light-duty conveying. Non-abrasive, low-density materials. | Provides basic dust containment. Simplified structural installation. | Bulk material pressure acts directly on the rubber, deflecting the seal and causing spillage and accelerated seal wear. |
| Steel Skirtboard + Internal Wear Liner + External Single-Lip Seal | General bulk solid containment, including abrasive materials. | Wear liner isolates the elastomer from bulk material pressure, extending seal life. | Requires maintenance of the 10 to 19 mm [3/8 to 3/4 in] steel-to-belt clearance. Inadequate for fluidised materials. |
| Steel Skirtboard + Internal Wear Liner + External Dual-Lip Seal | Dry, dusty and aerated bulk solids. | Primary lip contains bulk solids. Secondary lip captures fugitive particulate emissions. | Increases parasitic drag and drive torque. Requires impact beds to control dynamic belt sag. |
5. Belt Cleaning Systems
Fines and moisture adhere to the belt cover after discharge over the head pulley. Remove this carryback in stages and direct it into the discharge chute.
| Feature | Primary Cleaners (Pre-Cleaners) | Secondary Cleaners | Tertiary Cleaners and Wash Boxes | Return Ploughs (V-Ploughs and Diagonal Ploughs) |
|---|---|---|---|---|
| Location | On the head pulley face below the material trajectory, typically between the 3 o'clock and 5 o'clock positions for a belt travelling left to right. | Mounted on the flat return run immediately after the belt leaves the head pulley. | Mounted further down the return run, after the secondary cleaner. | Pulley-side (upper) surface of the return belt run, 3 to 5 m [10 to 16 ft] before the tail or gravity take-up pulley. |
| Primary Function | Peels the thickest layer of adhered bulk material. | Scrapes residual sticky fines, clay and moisture that pass the primary cleaner. | Provides a final wash and wipe for sticky materials (wet bauxite, clay, synthetic gypsum). | Deflects spilled or fugitive rocks off the belt edges to reduce tail pulley and belt carcass damage. |
| Action/Mechanism | Peels material away under constant contact pressure from pneumatic, spring or torsion tensioners. | Scrapes the flat belt surface. | Sprays a thin film of water to create a slurry, then wipes it clean. | Deflects material off both sides (V-plough) or one side (diagonal plough). |
| Blade Material | Cast PU, typically 70 to 85 Shore A. | Tungsten carbide tips brazed onto a steel or PU mounting cushion. | PU or soft rubber wiper blade, with water spray nozzles. | Typically heavy-duty PU or rubber. |
| Quantity Typically Required | Generally one cleaner per discharge head pulley. | One to three cleaners installed in sequence, depending on material stickiness and required cleanliness standards. | Usually one system per conveyor, applied only when primary and secondary cleaners are insufficient. | At least one before the tail pulley, plus one before each gravity take-up or bend pulley on the return run. |
| Material Type Recommendations | Suits most bulk materials, including heavy, dry or slightly moist aggregates, ores, coal and rock. | Materials that leave a sticky residue or film, such as moist fines, clay, wet sand and sticky ores. | Sticky, paste-like materials such as wet bauxite, heavy clay or synthetic gypsum, or applications with a near-zero carryback specification. | Use on all conveyors handling lump or granular material, particularly hard, sharp rock or gravel that punctures the belt if trapped. |
| Critical Setup Rules | Match blade width to the material path, typically belt width less 50 mm [2 in] for a flat belt, 100 mm [4 in] at 20 deg trough, 150 mm [6 in] at 35 deg and 200 mm [8 in] at 45 deg. Set blade-to-belt pressure to approximately 14 kPa [2 psi]. | Lean the blade 5 to 15 deg in the direction of belt travel. | Requires water supply plumbing and a catch basin and drainage system for the slurry. | Mount gravity-fed only (floating on a tether, chain or swing arm). Do not bolt rigidly to the structure. |
| Mechanical Splice Compatibility | Compliant PU accommodates mechanical splices without gouging. | Rigid carbide can dislodge fasteners. Specify cushioned segments or PU blades in place of carbide. | Soft rubber or PU wipers ride over mechanical splices. | Ploughs float on the pulley-side cover and ride over splices. |
| Consequences of Improper Setup | Excess pressure overheats and degrades the PU, and insufficient pressure allows carryback. If the blade is too wide, the blade edge cuts into the belt during lateral wander. | If angled against the direction of belt travel, surface defects or splices catch and damage the belt carcass. | Without drainage, the slurry causes spillage and drive pulley slip. | A rigidly mounted plough wears the pulley-side belt cover. |
6. Dust Control and Environmental Management
Transfer points are the main source of fugitive dust, as falling material displaces air and the turbulent updraft carries fines out through skirt gaps. Control dust by wet suppression, dry extraction or enclosure.
6.1 Dust Suppression
Wet suppression systems increase cohesive forces between particles to retain dust within the material flow, or capture airborne dust using fine water mist.
| Method | Mechanism and Application | Advantages | Disadvantages | Critical Constraints |
|---|---|---|---|---|
| Standard Water Sprays | Wets bulk material before or during transfer, so finer dust particles adhere to larger lumps. Suits open areas where bulk wetting is acceptable. | Low capital cost. Simple design and installation. Uses standard plant water pressure and requires minimal maintenance. | Consumes high volumes of water with risk of over-wetting material. Water beads due to high surface tension, limiting coverage. Less effective on airborne dust. Added moisture lowers the calorific value of coal and similar materials. | Blinding Limit: Limit added moisture to typically 0.5% to 1.0% by mass. Added moisture above 1.5% to 2.0% packs material in transfer chutes, blinds vibrating screen apertures and causes mistracking from mud build-up on return idlers. |
| High-Pressure Fogging (Atomisation) | Uses hydraulic pressure above 7 MPa [1,000 psi] to atomise water into 10 to 50 µm [0.4 to 2.0 mil] droplets. Droplets match dust size so they collide, agglomerate and fall back under gravity. Suits enclosed transfer chutes and crusher housings. | Captures airborne and respirable dust. Adds minimal moisture to the material flow. Avoids the aerodynamic deflection of dust around large droplets. | High capital cost for pump infrastructure. Wind and draughts disperse the fog. Provides no residual dust control. | Filtration and Enclosure Limits: Requires filtered water, since fine nozzles clog on minor impurities. Use only in enclosed air spaces, since wind on exposed belts disperses the fog before agglomeration occurs. |
| Air-Atomising Fogging (Dry Fog) | Mixes compressed air and low-pressure water in two-fluid nozzles to atomise water into droplets typically 1 to 10 µm [0.04 to 0.4 mil]. Suits hoppers, bins and fully enclosed transfer chutes for suppression of fine respirable dust. | Produces smaller droplets than hydraulic high-pressure fogging, improving respirable dust capture. Operates on standard plant water pressure and adds negligible moisture to the bulk material. | Consumes large volumes of compressed air at high energy cost. Nozzles generate high noise levels, and internal wear distorts the fog pattern. | Compressed Air and Containment Limits: A drop in plant air pressure causes the nozzles to discharge large droplets instead of dry fog. House within sealed enclosures, since ambient air movement disperses the droplets. |
| Surfactants (Wetting Agents) | Chemicals injected into spray water reduce surface tension, so a small volume of water coats a large surface area without beading. Suits hydrophobic materials such as coal and petroleum coke. | Reduces the water required and improves moisture penetration into the material bed. Lowers the risk of downstream screen blinding or chute plugging compared with plain water. | Incurs ongoing chemical costs and requires dosing and metering pumps. Chemical runoff raises environmental and regulatory concerns. | Blinding Limit and Dosing Calibration: Surfactants reduce the water required, but added moisture above 1.5% to 2.0% still causes chute packing and screen blinding. Calibrate dosing to avoid chemical runoff. |
| Foam Dust Suppression | Injects compressed air into a water and chemical surfactant mixture to generate an expanding foam. Applied at crushers or transfer points to cover bulk material and fill void spaces, expanding a small volume of water over a large surface area. | Provides high surface area coverage with low water usage. Foam blocks dust from escaping enclosures and provides some residual dust control for downstream conveyor transfers. | High ongoing cost of foaming chemicals. Requires a manifold supplied with both water and compressed air, increasing maintenance. | Turbulent Mixing Limit: Foam sprayed onto a static or moving belt surface is ineffective. Apply it at a crusher or active transfer point where mechanical agitation mixes the foam into the material bed. |
| Binders (Crusting Agents) | Chemical agents such as polymers or lignosulphonates sprayed onto the surface of a loaded belt as it leaves the plant, curing to form a solid crust over the material. Suits overland conveyors, rail wagons and stockpiles. | Reduces dust generation during long overland transit and provides long-lasting residual dust control. Protects against wind erosion and reduces bulk material loss. | High ongoing chemical cost. Requires curing time to harden. Provides no dust control during active material handling or processing. | Agitation and Curing Limits: The crust fractures if the material is transferred, crushed or agitated. Apply binders only at the final exit point of a plant, and allow undisturbed transit time for the crust to cure. |
| Water Curtains | Flat-fan nozzles project a continuous sheet of water across the open exit of a transfer chute or bunker, acting as a liquid barrier that captures airborne dust rather than wetting the material flow directly. | Simple to retrofit at problematic chute exits. Contains dust within an enclosure without treating the entire bulk material volume. | Does not treat the underlying cause of the dust. Easily disrupted by material flow and can cause localised over-wetting or pooling if not aligned correctly. | Material Clearance Limit: Align the curtain so the material profile passes beneath the water sheet. Material passing through the sheet breaks the barrier and over-wets the top layer. |
6.2 Dust Extraction
Where water addition is not permitted (e.g. cement clinker, grain or water-reactive chemicals), extract dust with a dry collection system such as a baghouse or cartridge collector.
A centrifugal exhaust fan draws air from the transfer chute to hold a slight negative pressure inside the skirted enclosure, so ambient air leaks inward through the skirt seal gaps and dust does not escape outward.
Size the exhaust fan on the sum of air displaced by the incoming material, air induced by the falling stream, air induced by the moving belt and air from any upstream crusher discharging into the chute. Exhaust a minimum of 0.54 m3/s per metre of belt width [350 ft3/min per ft] at belt speeds up to 1.0 m/s [200 fpm], and 0.77 m3/s per metre [500 ft3/min per ft] above 1.0 m/s [200 fpm]. Increase these rates 1.5 to 2.0 times for dry, dusty material.
Design for an inward air velocity of 0.75 to 1.0 m/s [150 to 200 fpm] at every open gap, crack or unsealed skirt edge in the loading zone. An oversized fan raises the capture velocity above 5.0 m/s [1,000 fpm], drawing saleable product off the belt and plugging the filter bags.
6.3 Wind Guards and Conveyor Enclosures
Crosswind accelerating over the troughed belt profile lowers the pressure above the belt and generates aerodynamic lift. Lift can raise an empty or lightly loaded belt out of the idler trough and, at sufficient wind speed, displace it from the conveyor structure. Provide wind protection where sustained crosswind exceeds 20 m/s [45 mph].
| Protection Method | Description | Advantages | Limitations | Recommended Applications |
|---|---|---|---|---|
| Wind Hoops | Heavy steel half-hoops bolted to the stringers over the carrying side of the belt, spaced 3.0 to 5.0 m [10 to 16 ft] apart. Retain the belt in the trough if lifted by wind. | Low capital cost. Simple and quick to install. Belt and material remain visible. Does not obstruct maintenance or idler replacement. | Does not deflect wind, and only retains the belt on the idlers. Offers no protection against rain, snow or ultraviolet (UV) degradation. Provides no dust control or protection against material blow-off. | Budget-constrained projects handling heavy or coarse, low-dust materials that require protection against belt displacement only. |
| Wind Guards / Deflectors | Solid or perforated plates mounted continuously along one or both sides of the conveyor stringers to block side winds. | Lower cost than full enclosures. Deflects wind and reduces belt lift. Leaves the top open for visual inspection of the material. Easier maintenance access than full hoods. | No top-down protection from rain, snow or UV degradation. Less effective at containing airborne dust than full enclosures. Protects one side only when installed on one side. | Sites requiring prevention of aerodynamic lift and material blow-off from crosswinds with visual access to the material. |
| Corrugated Hoods (Full Enclosure) | Half-cylinder corrugated steel, aluminium or fibreglass hoods covering the carrying run of the belt. | Shields the carrying run from wind and belt lift. Keeps rain and snow off the material. Protects the belt cover from UV degradation. Contains dust for environmental compliance. | Highest capital cost of the listed methods. Obstructs visual inspection of the belt and material. Requires hinged panels or removable sections for maintenance, making idler changes more time-consuming. | Conveyors handling dusty, moisture-sensitive or environmentally hazardous materials requiring full weather protection. |
| Return Idlers (Flat versus V-Return) | The empty return belt is also exposed to wind. On flat return idlers, bolt vertical steel drop plates to the stringer exteriors to block crosswind. V-return idlers restrain the belt laterally through the V profile, without external plates. | V-return idlers restrain the belt without added plates. Drop plates on flat returns stop the empty belt flipping or wandering off the idlers. | Drop plates add capital cost and can trap fugitive material if not designed with self-cleaning angles. V-return idlers require specific frames and cost more than standard flat returns. | Use V-return idlers on new designs in high-wind areas. Use drop plates as retrofits or on systems mandated to use flat return rolls. |
| Wind / Porous Fences | Freestanding, structurally supported porous screens built parallel to the conveyor line, reducing wind velocity before it reaches the conveyor. | Does not attach to or add weight to the conveyor structure. Protects walkways and personnel in addition to the belt. No interference with conveyor maintenance. | Requires additional area. Expensive for long conveyors. Does not protect the belt from precipitation or UV exposure. | Facilities with available area where protecting personnel and walkways is a priority, or where structural weight limits prohibit mounting enclosures directly on the conveyor. |
7. Conveyor-to-Conveyor Speed and Direction Alignment
The interface between the discharging and receiving conveyors imposes two mechanical demands on the receiving belt: a re-acceleration tension load, and a lateral momentum correction where the two conveyors are not parallel.
7.1 Re-Acceleration Loading on the Receiving Belt
Where a rock box or dead-stop transfer is used, bulk material arrives at the receiving belt with near-zero forward velocity. The receiving belt accelerates the material to belt speed through friction between the belt top cover and the material, adding tension to the carrying strand and wearing the cover while the material slips.
Metric: T_am = (Q / 3.6) * (v_b - v_0)
Imperial: T_am = 2.8755 * 10^-4 * Q * (v_b - v_0)
Where:
- T_am = Carrying strand tension to accelerate the material to belt speed (N) [lbf]
- Q = Throughput (t/h) [stph]
- v_b = Belt speed (m/s) [fpm]
- v_0 = Material velocity component in the direction of belt travel at loading (m/s) [fpm]
Engineering Takeaway: Tension depends on mass flow and the speed deficit at loading, not on skirt length or friction coefficient. Add tension to the effective tension when sizing the drive and checking the belt rating. Velocity-matched chutes reduce both tension and the slip that wears the top cover.
Metric: L_a = (v_b^2 - v_0^2) / (2 * mu_m * g)
Imperial: L_a = (v_b^2 - v_0^2) / (7,200 * mu_m * g)
Where:
- L_a = Length over which material slides on the belt before reaching belt speed (m) [ft]
- v_b = Belt speed (m/s) [fpm]
- v_0 = Material velocity component in the direction of belt travel at loading (m/s) [fpm]
- mu_m = Coefficient of friction between bulk material and the belt top cover (dimensionless), typically 0.5 to 0.7 for dry granular material and 0.3 to 0.5 for wet or cohesive material
- g = Gravitational acceleration, 9.81 (m/s2) [32.2 ft/s2]
Note: The formula assumes a horizontal belt and sliding at the base of the material bed.
Engineering Takeaway: Material slides on the top cover over L_a. Extend the skirtboard and impact support beyond L_a, and allow a longer L_a for wet or cohesive material with a lower mu_m.