1. Tensioning and Take-Up Systems
The take-up system maintains slack-side belt tension (T2) to prevent drive pulley slip and absorbs belt elongation.
2. Elongation Characteristics and Take-Up Implications
Elastic elongation (stretch under load) and permanent elongation (constructional stretch during run-in) are the principal components of take-up travel. Where travel is insufficient, the carriage reaches its end stop, T2 falls and the drive pulley slips.
| Belt Type / Material | Weave | Permanent Elongation % (Run-In) | Elastic Elongation % (at Rated Working Tension) |
|---|---|---|---|
| CC (Cotton/Cotton) | Plain Weave | 1.50 to 2.50 | 1.00 to 2.00 |
| CN (Cotton/Nylon) | Plain Weave | 1.50 to 2.00 | 1.50 to 2.00 |
| NN (Nylon/Nylon) | Plain / Twill Weave | 1.50 to 2.00 | 1.50 to 2.00 |
| NN (Nylon/Nylon) | Crowfoot Weave | 1.00 to 1.50 | 1.50 to 2.00 |
| PN / EP (Polyester/Nylon) | Plain / Twill Weave | 0.75 to 1.00 | 1.00 to 1.50 |
| PN / EP (Polyester/Nylon) | Crowfoot Weave | 0.50 to 0.75 | 0.50 to 1.00 |
| EE (Polyester/Polyester) | Plain / Twill Weave | 0.75 to 1.00 | 1.00 to 1.50 |
| EE (Polyester/Polyester) | Crowfoot Weave | 0.50 to 0.75 | 0.50 to 1.00 |
| Polyester | Straight-Warp | 0.20 to 0.50 | 0.50 to 1.00 |
| Polyvinyl Chloride (PVC) | Solid Woven | 0.75 to 2.00 | 0.75 to 2.00 |
| PVG (PVC-impregnated carcass, nitrile rubber covers) | Solid Woven | 0.75 to 1.50 | 0.75 to 1.50 |
| Aramid | Conventional Weave | 0.25 to 0.50 | 0.25 to 0.40 |
| Aramid | Straight-Warp | 0.15 to 0.25 | 0.15 to 0.25 |
| Steel Cord (ST) | Not applicable | 0.10 to 0.25 | 0.10 to 0.20 |
Note: Values are typical ranges at 20 deg C [68 deg F]. Confirm against the belt manufacturer's elongation data for final design.
3. Types of Take-Up Systems
Selection is dictated by conveyor length, operating environment, and starting and stopping dynamics.
| Configuration | Description / Mechanism | Typical Conveyor Length | Advantages | Limitations |
|---|---|---|---|---|
| Horizontal | The take-up pulley is mounted on a wheeled or sliding carriage that travels horizontally along guide rails. | Medium to long, including conveyors greater than 5 km [3.1 mi] | Ground-level mounting provides good maintenance access and accommodates large travel distances without tall structural towers. | Requires a large horizontal footprint. Ground-level rails accumulate dirt, spillage, or ice, which can jam or derail the carriage wheels. |
| Vertical | The take-up pulley hangs vertically beneath the conveyor or is suspended within a dedicated structural tower. The counterweight can hang directly from the pulley carriage, or wire ropes can transfer the load to a separate tensioning source such as a ground-mounted winch or a separate gravity tower. | Short to medium, up to 3 km [1.9 mi] | Minimal horizontal footprint. Suited to gravity counterweight systems in space-constrained plants. | Requires structural steel towers, typically 10 to 20 m [33 to 66 ft] high. Maintenance requires work at height, and travel stroke is limited by tower height or ground clearance. |
| Multilayer (Festoon or Belt Storage Unit, BSU) | The belt is reeved into multiple parallel strands to store slack. The unit can be configured horizontally or vertically, with 4-strand and 6-strand horizontal units typical underground. Storage capacity equals carriage travel multiplied by the number of strands (e.g. a 50 m [164 ft], 6-strand take-up holds 300 m [984 ft] of belt). As the mining face advances, a winch feeds this stored belt into the system. When storage is depleted, the carriage retracts during scheduled maintenance and a new belt roll is spliced in to replenish storage. | Long, advancing and retreating systems, from 2 km [1.2 mi] to more than 20 km [12 mi] | Stores large belt lengths in a compact footprint. Suited to tunnel boring and underground mining where conveyor length changes continuously. | Higher complexity and capital cost. Multiple bend pulleys increase rotating resistance, bending stress, and cover wear, and complicate belt threading and splicing. |
| Force Method | Mechanism / Control Logic | Typical Conveyor Length | Advantages | Limitations |
|---|---|---|---|---|
| Screw (Manual) | Threaded rods with manual adjustment nuts push the tail pulley rearward. | Very short, light-duty (less than 50 m [164 ft]) | Lowest capital cost and simplest installation. Requires no electricity, sensors, or active control, and has a small footprint. | No dynamic response. The rigid constraint cannot absorb elastic starting stretch, so belts are typically over-tensioned to avoid slip, which reduces bearing life and increases splice fatigue. Unequal adjustment of the left-hand and right-hand screws skews the pulley and causes belt mistracking. Load cell monitoring is difficult to retrofit. |
| Hydraulic / Pneumatic | Fluid cylinders push or pull the carriage and tension is regulated by pressure-regulating valves. | Short (less than 100 m [328 ft]) | Compact installation that maintains constant tension through fluid pressure regulation. Suited to mobile crushers or confined underground transfer points. | Cylinder stroke is typically less than 2 m [6.6 ft]. High-stretch fabric belts require manual cylinder reset to extend travel. Prone to fluid leaks in harsh environments. |
| Gravity (Counterweight) | A steel or concrete counterweight is suspended from the carriage by wire ropes or directly connected to the pulley. | Medium to long (50 to 3,000 m [164 to 9,840 ft]) | Maintains constant T2 at steady state. The counterweight displaces automatically to absorb starting stretch without sensors, programming, or electricity. Responds passively to tension variation with no control lag. | Counterweight free-fall hazard if the belt fails. Typically requires a vertical tower structure to house the counterweight. |
| Fixed Winch (Electric Screw) | A motorised winch pulls the carriage until a limit switch operates. A failsafe brake then locks the drum to hold the wire rope position. | Short to medium (less than 500 m [1,640 ft]) | Provides a positive lock on the carriage with simple electrical controls and a mechanical wire rope brake. | Once the brake engages, the system behaves as a rigid take-up and cannot absorb starting transients, causing tension spikes in the belt. |
| Semi-Active Winch (Stepped) | The failsafe winch brake releases to allow the drum to wind in or pay out wire rope when tension limits are exceeded, then reapplies to hold position. A Programmable Logic Controller (PLC) compares a load cell signal with a high setpoint and a low setpoint. | Medium to long (100 to 5,000 m [328 to 16,400 ft]) | Adapts to belt stretch and permanent elongation over time, reducing tension overloads. | Delayed response causes the system to hunt around the tension setpoint. Repeated brake cycling induces carriage oscillation and accelerates brake pad wear. |
| Fully Active Winch (Dynamic) | A Variable Frequency Drive (VFD) controlled motor maintains tension through a continuous Proportional-Integral-Derivative (PID) loop with zero-speed torque hold. The failsafe brake remains released during operation and clamps only when the conveyor is stopped or on power failure. Suited to high-tension and underground conveyors where gravity tower height or travel capacity is a constraint. A single-reeved winch typically achieves carriage velocities of 0.3 to 1.0 m/s [60 to 200 fpm]. | Medium to long (500 m [1,640 ft] to more than 20 km [12 mi]) | Pays out or retracts wire rope to absorb tension transients as they occur. Reduces peak tensions, which can permit a lower belt carcass rating. | Highest capital cost of the force application methods. Requires advanced programming, PID tuning, and ongoing electrical maintenance. Response velocity is constrained by carriage inertia, motor torque, and gearbox ratio. Size the motor and gearbox for both the required carriage acceleration and the holding torque to track elastic transients during starting and stopping. |
4. Take-Up System Selection Guide
The following decision matrix provides a structured basis for take-up type selection.
| Parameter | Screw (Manual) | Gravity (Counterweight) | Hydraulic / Pneumatic | Fixed Winch | Semi-Active Winch | Fully Active Winch |
|---|---|---|---|---|---|---|
| Conveyor Centre Distance | Less than 50 m [164 ft] | 50 to 3,000 m [164 to 9,840 ft] | Less than 100 m [328 ft] | Less than 500 m [1,640 ft] | 100 to 5,000 m [328 to 16,400 ft] | Greater than 500 m [1,640 ft], no fixed upper limit |
| Compatible Carcass Types | EP/PN, ST, aramid | All types | EP/PN, ST, aramid | ST, aramid, EP/PN | All types | All types |
| Dynamic Startup Absorption | None | Passive (constant T2) | Limited by stroke | None | Stepped | Continuous, real-time |
| Vertical Clearance Required | Minimal | 10 to 20 m [33 to 66 ft] tower | Minimal | Minimal | Minimal | Minimal |
| Power Supply Required | None | None | Hydraulic power unit | Yes | Yes | Yes (VFD) |
| Control Complexity | None | None | Low | Low | Medium | High (PID, load cell) |
| Relative Capital Cost | Very Low | Medium | Low to Medium | Low | Medium | High |
| Underground Application | Short headings only | Not practical | Transfer points only | Unsuitable | Suitable | Preferred |
| Mobile Plant Application | Yes (short conveyors) | No | Yes | No | No | No |
| Long-Distance Application | No | Yes (if clearance permits) | No | No | Acceptable | Preferred |
| Key Limitation | No dynamic response. Over-tensioning risk. | Gravity tower footprint and height. Falling weight hazard. | Short stroke. Requires manual carriage reset for long belts. | Rigid once locked. Tension spikes on start. | Carriage hunting. Delayed response. | High capital and commissioning cost. PID tuning required. |
5. Calculating Minimum Loop Take-Up Travel
Minimum take-up travel is the sum of the components in the table below.
| Parameter | Component Name | Description | Typical Values |
|---|---|---|---|
| TU_elas | Elastic elongation allowance | Absorbs reversible elastic belt stretch caused by varying operating tensions (e.g. starting, stopping, loaded versus empty). | Typically 0.10% to 2.0% of belt length, depending on carcass type. Carriage travel required is belt stretch divided by the number of belt strands, N. For a standard 2-strand loop, 1.0 m [3.3 ft] of carriage travel absorbs 2.0 m [6.6 ft] of belt stretch. |
| TU_perm | Permanent elongation allowance | Absorbs irreversible constructional carcass stretch that occurs during the belt's initial run-in period. | Typically 0.15% to 2.5% of total belt length for textile and solid woven belts, and 0.10% to 0.25% for steel cord belts. Carriage travel required is this length divided by N. |
| TU_splc | Splice length allowance | Provides sufficient slack to pull the belt ends together for planned maintenance, repair, or vulcanising. | 0.10 to 5.0 m [4 in to 16 ft] or more of belt consumed per splice event, depending on joint type, belt width and splice design. A replacement splice consumes approximately twice this length. Carriage travel required equals the splice length divided by N. |
| TU_safe | Safety buffer at each end of travel | Maintains physical clearance between the moving carriage and structural end stops during dynamic surges (e.g. emergency stops). | 0.2 to 2.0 m [8 to 79 in] minimum physical clearance required at both the forward and reverse travel limits to prevent mechanical impact. |
| TU_stor | Belt storage allowance | Stores excess belt to sustain continuous mining face advance (or retreat) without frequent belt cuts or additions. | Carriage travel is the stored belt length divided by N (e.g. storing 100 m [328 ft] of excess belt in a 4-strand BSU requires 25 m [82 ft] of carriage travel). |
5.1 Elastic Elongation Allowance
TU_elas = (e_elas / 100) * C
Where:
- TU_elas = Carriage travel required to absorb elastic belt elongation (m)
- e_elas = Elastic elongation of the carcass at rated working tension (%)
- C = Conveyor centre distance measured along the belt path between head and tail pulleys, including all rises and falls (m)
Engineering Takeaway: The allowance is based on C rather than on belt circuit length because the circuit is approximately 2 times C and a single-pulley take-up absorbs twice its travel in belt length. Applying elongation at rated working tension over the full belt length is conservative, as the average belt tension is lower.
5.2 Permanent Elongation Allowance
TU_perm = (e_perm / 100) * C
Where:
- TU_perm = Carriage travel required to absorb permanent constructional elongation (m)
- e_perm = Permanent elongation of the carcass over the run-in period (%)
- C = Conveyor centre distance measured along the belt path between head and tail pulleys, including all rises and falls (m)
Engineering Takeaway: Permanent elongation occurs progressively, typically over the first 3 to 6 months of operation, as the carcass weave or cable geometry settles under tension. For cotton and nylon carcasses, permanent elongation equals or exceeds elastic elongation and can govern take-up travel. For steel cord belts, permanent elongation is small as a percentage but amounts to several metres of carriage travel on long overland conveyors.
5.3 Splice Length Allowance
Splicing progressively reduces total belt length. Provide sufficient travel to absorb this reduction without relocating the take-up pulley.
For surface conveyors with a design life of 15 to 20 years, the number of planned splices is typically 6 to 12 for a single-circuit belt. For underground development conveyors at high face advance rates, the planned splices can exceed 50 over a 12-month cycle.
TU_splc = n_s * (L_splice / 2)
Where:
- TU_splc = Carriage travel required to accommodate planned splicing (m)
- n_s = Number of planned splices over the design service life (dimensionless)
- L_splice = Length of belt consumed per splice joint (m)
- 2 = Belt-to-carriage travel ratio for standard single-pulley take-up configurations (dimensionless)
Engineering Takeaway: Omitting the splice allowance from the take-up specification causes the carriage to reach its end stop before the end of belt life, particularly on systems with long splices and high splice frequencies.
L_splice = (n_st * L_st) + (k_b * B)
Where:
- L_splice = Length of belt consumed per splice event (m) [ft]
- n_st = Number of steps in the splice (dimensionless). For multi-ply fabric, n_st = N - 1, where N is the number of plies. For steel cord, take n_st from the splice design.
- L_st = Step length from the belt manufacturer’s splice design (m) [ft]
- k_b = Bias factor: 0.3 or 0.4 as specified, or 0 for a square splice (dimensionless)
- B = Belt width (m) [ft]
Note: A splice that replaces an existing splice shortens the belt loop by approximately 2 * L_splice, because the old splice is cut out before the new one is made. Use 2 * L_splice for each planned replacement splice.
Engineering Takeaway: Bias length rises with belt width and can exceed the total step length on wide belts with few plies. A 4-ply belt 1,200 mm [48 in] wide with 300 mm [12 in] steps and a 0.3 bias consumes 3 * 0.30 + 0.3 * 1.2 = 1.26 m [4.1 ft] per splice.
| Splice Type | Belt Length Consumed per Splice |
|---|---|
| Mechanical fastener | 0.10 to 0.20 m [4 to 8 in] |
| Hot or cold vulcanised stepped, multi-ply fabric | 0.4 to 2.0 m [1.3 to 6.6 ft] |
| Finger splice (solid woven, straight-warp, aramid) | Finger length plus bias, from the belt manufacturer’s splice design |
| Hot vulcanised steel cord, single-step | From 1.0 m [3.3 ft], plus bias |
| Hot vulcanised steel cord, multi-step high-tension | 4.0 to 5.0 m [13 to 16 ft] or more, plus bias |
Note: Fabric values are calculated with Formula 4 for 2 to 5 plies, step lengths of 0.20 to 0.35 m [8 to 14 in], belt widths of 600 to 1,800 mm [24 to 72 in] and a 0.3 bias. Confirm step lengths with the belt manufacturer.
5.4 Safety Buffer at Each End of Travel
The extended-end buffer (carriage at maximum forward travel with belt at maximum elongation) provides clearance for peak elastic elongation, thermal expansion, and carcass variability. Contact with the extended-end stop transfers the take-up force to the stop, reducing T2 and causing drive slip.
The retracted-end buffer (carriage at maximum rearward travel with belt at minimum elongation) accommodates an un-elongated new belt and dynamic starting transients. Contact with the retracted-end stop makes the take-up rigid and causes tension spikes during drive acceleration or deceleration.
Typical minimum safety buffers at each end of travel:
- Screw take-up: 200 to 400 mm [8 to 16 in] each end
- Gravity take-up: 400 to 600 mm [16 to 24 in] each end
- Hydraulic or pneumatic take-up: 300 to 500 mm [12 to 20 in] each end
- Fixed winch: 400 to 600 mm [16 to 24 in] each end
- Semi-active winch: 500 to 1,000 mm [20 to 39 in] each end
- Fully active winch: 800 to 1,500 mm [31 to 59 in] each end
- Multilayer loop take-up: 1,000 to 2,000 mm [39 to 79 in] each end
TU_safe = d_ext + d_ret
Where:
- TU_safe = Total safety buffer contribution to minimum take-up travel (m)
- d_ext = Safety clearance at the extended (maximum elongation) end of travel (m)
- d_ret = Safety clearance at the retracted (minimum elongation) end of travel (m)
On active winch systems, the extended-end safety buffer functions as a response-time reserve. Size d_ext so that the time for the carriage to traverse it exceeds the combined PID loop response and mechanical brake release times. For example, at a carriage velocity of 0.5 m/s [100 fpm], a 1.0 m [39 in] buffer provides 1.0 / 0.5 = 2.0 s of response time before end-stop contact.
Engineering Takeaway: For marginal response-time budgets, increase the safety buffer rather than retuning the PID loop aggressively, which can induce sustained carriage oscillation and accelerate component wear.
5.5 Total Minimum Take-Up Travel for a Standard Single-Pulley Configuration
TU_min = ((e_elas + e_perm) / 100) * C + (n_s * L_splice / 2) + (d_ext + d_ret)
Where:
- TU_min = Minimum required take-up travel for a standard single-pulley take-up (m)
- e_elas = Elastic elongation at rated working tension (%)
- e_perm = Permanent elongation over the run-in period (%)
- C = Conveyor centre distance measured along the belt path between head and tail pulleys, including all rises and falls (m)
- n_s = Number of planned splices over the design service life (dimensionless)
- L_splice = Length of belt consumed per splice (m)
- d_ext = Safety clearance at extended end of travel (m)
- d_ret = Safety clearance at retracted end of travel (m)
Engineering Takeaway: This calculation assumes a reference temperature of 20 deg C [68 deg F]. For elevated or sub-zero environments, adjust TU_min for the temperature dependence of carcass elongation and belt length. Add the design contingency for the conveyor category before specifying the take-up frame length.
5.6 Total Minimum Take-Up Travel for a Multilayer Configuration
Underground development conveyors with a multilayer loop take-up require internal belt storage capacity to sustain face advance operations between planned splices. This requirement is independent of elongation and splice parameters and adds to them in the total carriage travel.
BSC = R_adv * n_w * 2
Where:
- BSC = Minimum belt storage capacity required in the BSU (m)
- R_adv = Mining face advance per planned maintenance window (m)
- n_w = Number of planned maintenance windows between each belt splice event (dimensionless)
- 2 = Carry and return strand factor (dimensionless)
Engineering Takeaway: Each metre of conveyor extension draws 2 m of belt from storage. Lengthening the interval between splice events reduces splicing frequency but increases BSC and the required carriage travel.
TU_BSU = (((e_elas + e_perm) / 100) * L_belt + (n_s * L_splice) + BSC) / N + (d_ext + d_ret)
Where:
- TU_BSU = Total minimum take-up carriage travel for a BSU configuration (m)
- e_elas = Elastic elongation at rated working tension (%)
- e_perm = Permanent elongation over the run-in period (%)
- L_belt = Total belt circuit length at maximum development extent (m)
- n_s = Total number of planned splices over the development cycle (dimensionless)
- L_splice = Length of belt consumed per splice (m)
- BSC = Required belt storage capacity (m)
- N = Number of belt strands in the BSU loop (dimensionless)
- d_ext = Safety clearance at extended end of carriage travel (m)
- d_ret = Safety clearance at retracted end of carriage travel (m)
Engineering Takeaway: In a multilayer loop take-up, carriage translation absorbs N times its displacement in belt length, compared to the 2 times multiplier of a standard single-pulley configuration. Safety clearances (d_ext + d_ret) are physical carriage position limits on the rails and are added directly without division by N. Base all elongation and splice calculations on the total belt circuit length at maximum development extent.
5.7 Additional Loop Take-Up Contingency
The calculated take-up travel is the minimum value based on mean published elongation coefficients at standard reference conditions. Add the contingency below to cover carcass elongation manufacturing variability, mid-life sectional belt replacement, future conveyor extension, and thermal elongation deviation from the 20 deg C [68 deg F] reference condition.
| Conveyor Category | Centre Distance m [ft] | Design Contingency |
|---|---|---|
| Short plant | Less than 100 [328] | 10% |
| Medium | 100 to 1,000 [328 to 3,280] | 10% to 12% |
| Long | Greater than 1,000 [3,280] | 12% to 15% |
| Multilayer loop take-up | Not applicable | 15% plus 2.0 m [6.6 ft] of carriage travel |
Note: Contingencies are typical design practice, not standard-mandated values. Apply them to the calculated minimum travel, TU_min or TU_BSU.