1. Belt Mass, Roll Sizes and Storage
Belt mass and roll dimensions determine structural loads, drive inertia, lifting equipment and transport configuration. Storage conditions and inspection determine whether a stored belt is fit to install.
2. Belt Mass and Thickness
The cover mass factor is numerically equal to the specific gravity of the cover compound, typically 1.10 to 1.15 kg/m2 per mm [5.7 to 6.0 lb/ft2 per in] for standard grades. Fire-resistant and oil-resistant compounds are denser.
G = t_c + t_top + t_bot
Where:
- G = Total belt thickness (mm)
- t_c = Carcass thickness (mm)
- t_top = Top cover thickness (mm)
- t_bot = Bottom cover thickness (mm)
Engineering Takeaway: Total belt thickness governs roll diameter and therefore transport height. For a given belt length, roll cross-sectional area is proportional to G, so cover thickness added for wear life reduces the belt length that fits within a transport height limit.
m_A = m_c + (t_top + t_bot) * k_cov
Where:
- m_A = Belt mass per unit area (kg/m2)
- m_c = Carcass mass per unit area (kg/m2)
- t_top = Top cover thickness (mm)
- t_bot = Bottom cover thickness (mm)
- k_cov = Cover mass factor (kg/m2 per mm)
Engineering Takeaway: On fabric belts, cover mass can exceed carcass mass, so cover thickness and compound specific gravity govern belt mass. A fire-resistant above-ground cover compound is approximately 26% heavier per unit thickness than a general purpose compound.
W_b = m_A * B
Where:
- W_b = Belt mass per unit length (kg/m)
- m_A = Belt mass per unit area (kg/m2)
- B = Belt width (m)
Note: Add the spool or core tare mass, obtained from the manufacturer, to the total belt mass to determine shipping mass.
Engineering Takeaway: Belt mass is the belt mass input to idler loads, sag tension, effective tension and drive inertia. The minimum belt tension for sag control on the return run is directly proportional to belt mass.
| Number of Plies | Construction | Working Tension Equivalent PIW | Carcass Mass kg/m2 [lb/ft2] | Carcass Thickness mm [in] | Approximate Elastic Modulus kN/m [lbf/in] |
|---|---|---|---|---|---|
| 2-Ply | EP 250 | 143 | 2.8 [0.57] | 2.2 [0.09] | 2,500 [14,300] |
| 2-Ply | EP 400 | 228 | 4.4 [0.90] | 3.3 [0.13] | 4,000 [22,800] |
| 3-Ply | EP 630 | 360 | 5.1 [1.04] | 3.9 [0.15] | 6,300 [36,000] |
| 4-Ply | EP 800 | 457 | 6.8 [1.39] | 5.3 [0.21] | 8,000 [45,700] |
| 4-Ply | EP 1000 | 571 | 7.7 [1.58] | 6.1 [0.24] | 10,000 [57,100] |
| 5-Ply | EP 1250 | 714 | 9.6 [1.97] | 7.8 [0.31] | 12,500 [71,400] |
| 5-Ply | EP 1600 | 914 | 11.9 [2.44] | 9.3 [0.37] | 16,000 [91,400] |
| 5-Ply | EP 2000 | 1,140 | 14.5 [2.97] | 11.0 [0.43] | 20,000 [114,200] |
| 5-Ply | EP 2500 | 1,430 | 18.0 [3.69] | 13.5 [0.53] | 25,000 [142,800] |
Note: Values are for the carcass only and are typical. Obtain construction data from the manufacturer. EP denotes a polyester warp and polyamide weft fabric carcass. The working tension equivalent, in pounds per inch of width (PIW), is the rated breaking strength divided by a 10:1 safety factor, converted at 5.71 PIW per kN/m. The elastic modulus is taken as 10 times the rated breaking strength.
| ISO Rating kN/m | Working Tension Equivalent PIW | Carcass Mass kg/m2 [lb/ft2] | Carcass Thickness mm [in] |
|---|---|---|---|
| 630 | 355 | 7.8 [1.60] | 4.6 [0.18] |
| 800 | 455 | 9.5 [1.95] | 5.8 [0.23] |
| 1,000 | 570 | 11.1 [2.27] | 6.9 [0.27] |
| 1,250 | 710 | 11.7 [2.40] | 7.4 [0.29] |
| 1,600 | 910 | 13.3 [2.72] | 8.6 [0.34] |
| 1,800 | 1,025 | 14.5 [2.97] | 9.6 [0.38] |
| 2,000 | 1,140 | 16.0 [3.28] | 10.8 [0.43] |
| 2,500 | 1,425 | 18.5 [3.79] | 12.5 [0.49] |
Note: Values include the base polyvinyl chloride (PVC) impregnation and are typical. Obtain construction data from the manufacturer. Calculate the external cover mass with the cover mass factor of the cover compound, typically 1.28 to 1.40 kg/m2 per mm [6.7 to 7.3 lb/ft2 per in]. The working tension equivalent is approximately one-tenth of the rated breaking strength.
| Construction | Carcass Mass kg/m2 [lb/ft2] | Carcass Thickness mm [in] |
|---|---|---|
| ST 500 | 8.0 [1.64] | 4.0 [0.16] |
| ST 800 | 11.0 [2.25] | 4.5 [0.18] |
| ST 1000 | 14.0 [2.87] | 5.5 [0.22] |
| ST 1250 | 16.0 [3.28] | 6.0 [0.24] |
| ST 1600 | 18.0 [3.69] | 6.5 [0.26] |
| ST 2000 | 20.0 [4.10] | 7.0 [0.28] |
| ST 2500 | 23.0 [4.71] | 8.0 [0.31] |
| ST 3150 | 27.0 [5.53] | 9.0 [0.35] |
| ST 3500 | 29.0 [5.94] | 9.5 [0.37] |
| ST 4000 | 32.0 [6.55] | 10.5 [0.41] |
| ST 4500 | 36.0 [7.37] | 11.5 [0.45] |
| ST 5400 | 42.0 [8.60] | 13.0 [0.51] |
| ST 6300 | 47.0 [9.63] | 14.5 [0.57] |
| ST 7000 | 52.0 [10.65] | 16.0 [0.63] |
| ST 7500 | 56.0 [11.47] | 17.5 [0.69] |
| ST 8000 | 60.0 [12.29] | 19.0 [0.75] |
| ST 10000 | 65.0 [13.31] | 21.0 [0.83] |
Note: Values are for the carcass only. ST denotes a steel cord carcass. Mass and thickness are approximations with an accuracy of +/- 10%. Obtain construction data from the manufacturer.
| Compound | Cover Mass Factor kg/m2 per mm [lb/ft2 per in] |
|---|---|
| Low Rolling Resistance (LRR) | 1.09 [5.7] |
| High Abrasion (SAR / DIN W) | 1.10 [5.7] |
| General Purpose (DIN Y / RMA Grade II) | 1.11 [5.8] |
| Heavy Impact (DIN X / RMA Grade I) | 1.11 [5.8] |
| Cold Weather | 1.11 [5.8] |
| Heat Resistant (EPDM / SBR) | 1.05 [5.5] |
| Extreme Heat (Chlorobutyl) | 1.15 [6.0] |
| Oil Resistant (NBR) | 1.16 [6.0] |
| Moderate Oil Resistant (CR) | 1.40 [7.3] |
| Fire Resistant, Above Ground (SBR/CR) | 1.40 [7.3] |
| Fire Resistant, Underground (PVC/NBR) | 1.28 [6.7] |
| Ceramic Embedded | 1.50 or greater [7.8 or greater] |
Note: Values are numerically equal to typical compound specific gravities. Compound abbreviations are styrene-butadiene rubber (SBR), ethylene propylene diene monomer (EPDM), chloroprene rubber (CR) and nitrile butadiene rubber (NBR). Obtain the specific gravity from the compound data sheet for final mass calculations.
3. Roll Dimensions
Calculate roll dimensions to confirm the belt meets transport height and width limits.
Metric: D = SQRT(d^2 + 0.001273 * L * G)
Imperial: D = SQRT(d^2 + 15.3 * L * G)
Where:
- D = Outer roll diameter (m) [in]
- d = Core or spool outer diameter (m) [in]
- L = Belt length (m) [ft]
- G = Total belt thickness (mm) [in]
Note: The core or spool outer diameter is typically 0.30 to 0.60 m [12 to 24 in]. Add the packaging allowance to the calculated diameter. Confirm the minimum core diameter and the packaging allowance with the manufacturer.
Engineering Takeaway: Where d is small relative to D, D increases with the square root of L, so doubling the belt length increases D by approximately 41%. Splitting the belt into shorter rolls reduces D but adds one field splice per additional roll.
Where a circular roll exceeds the transport height limit, wind the belt around two cores to form a racetrack roll of reduced height.
Metric: C = ((L * G / 1000) - 0.7854 * (D^2 - d^2)) / (D - d)
Imperial: C = ((12 * L * G) - 0.7854 * (D^2 - d^2)) / (D - d)
Where:
- C = Centre distance between the two cores (m) [in]
- D = Outer roll diameter at the racetrack ends, set to the maximum allowable roll height less the packaging allowance (m) [in]
- d = Core outer diameter (m) [in]
- L = Belt length (m) [ft]
- G = Total belt thickness (mm) [in]
Note: The overall racetrack roll length is C + D.
Engineering Takeaway: A negative centre distance indicates that a circular roll fits within the height limit. Reducing outer diameter increases centre distance, so check the overall roll length against the trailer deck length and the laydown area.
Metric: L = PI * N * (D + d) / 2
Imperial: L = PI * N * (D + d) / 24
Where:
- L = Belt length on the roll (m) [ft]
- N = Number of complete wraps (dimensionless)
- D = Outer roll diameter (m) [in]
- d = Core outer diameter (m) [in]
Engineering Takeaway: Confirm the length on a spare or part-used roll before allocating it to a replacement, as the label length may not reflect earlier cuts. A miscount of one wrap introduces an error equal to one mean wrap circumference.
4. Lifting and Handling
| Requirement | Reason |
|---|---|
| Lift with a rated bar or pipe through the core and a spreader bar above the roll. | Keeps slings clear of the roll edges. |
| Do not sling around the roll circumference. | Slings crush and cut the belt edges. |
| Transport and store rolls upright with the core axis horizontal. Do not lay rolls flat on their side. | A roll laid flat telescopes as the inner wraps displace axially, and the lower edge is crushed. |
| For long-term storage, suspend the roll on a bar through the core supported on A-frames. | Prevents flat spots from roll mass bearing on the circumference. |
| Rate the core bar, spreader and slings for the roll mass plus core or spool tare, and confirm current inspection tags. | Prevents rigging overload. |
5. Storage
Rubber covers degrade in storage by ozone attack on unsaturated polymer chains, ultraviolet (UV) oxidation and heat ageing. Moisture wicks into exposed cut ends and degrades the carcass. Aramid loses strength under UV exposure. Seal all cut ends before storage.
| Parameter | Requirement |
|---|---|
| Temperature | Below 25 deg C [77 deg F], preferably below 15 deg C [59 deg F] |
| Relative humidity | Below 70%, with no condensation or standing water |
| Light | Darkness or low-intensity artificial light. No direct sunlight. Shield the roll from UV-emitting sources such as fluorescent tubes. |
| Ozone | No electric motors, switchgear, transformers or welding equipment in the storage area |
| Atmosphere | Free of solvents, fuels, acids and oxidisers |
| Outdoor storage (where unavoidable) | Roll elevated on concrete or timber cribbing under an opaque, breathable cover. Do not use sealed polyethylene wrap, which traps condensation. |
| Rubber Group | Typical Belt Compounds | Initial Storage Period Years | Extension After Inspection and Testing Years |
|---|---|---|---|
| A | NR, SBR, BR | 5 | 2 |
| B | NBR, CR, IIR | 7 | 3 |
| C | EPDM | 10 | 5 |
Note: Periods run from the date of manufacture. For a blend of compounds from different groups, apply the shorter period. NR denotes natural rubber, BR butadiene rubber and IIR isobutylene isoprene (butyl) rubber.
Where the initial period has expired, inspect the belt and test a full-width sample for tensile strength, elongation at break and cover-to-carcass adhesion against the original certificate before applying the extension or installing the belt.
6. Inspection of Stored Belts
Inspect stored belts at intervals not exceeding 12 months, reduced to 6 months for belts stored outdoors or within 12 months of the end of their storage period.
| Check | Method | Action |
|---|---|---|
| Cover cracking | Visual survey of the outer wrap and cut ends for ozone cracking and crazing. Photograph for trend comparison. | Test before installation where cracking is present |
| Cover hardness | Shore A durometer at three points on the outer wrap, compared with the manufacturer's certificate | Test before installation where hardness exceeds the certificate value by more than 5 Shore A |
| Edges | Inspect for crushing, chunking and exposed carcass | Record and assess |
| Cut-end seals | Confirm seals are bonded and intact | Reseal |
| Core or spool | Check for corrosion, ovality and an unobstructed lifting bore | Rectify before lifting |
| Storage environment | Record temperature, humidity and any new ozone sources | Correct non-compliance |
| Records | Update the spares register with date, inspector, findings, photographs and remaining storage period | Not applicable |
7. Pre-Installation Acceptance
Do not install a belt that fails any check.
| Check | Acceptance Criterion |
|---|---|
| Identification | Manufacturer, batch, construction designation, width and manufacture date legible on the outer wrap |
| Length | Within the supplier's stated tolerance of the purchase specification |
| Storage period | Within the ISO 2230 period for the compound, or test results conforming to the original certificate |
| Covers and edges | No cracks, gouges, embedded objects or blisters on the outer wrap. Inspect the full length as the belt is pulled into the structure and record any finding. |
| Cut ends | Clean and square. No moisture staining, carcass degradation or cord corrosion. |
| Splice markings | Pre-marked splice reference lines intact and straight, where supplied |
| Transport damage | No impact damage, edge crushing or telescoping |