1. Belt Power and Tensions

Conveyor drive power is determined by a force balance. At constant belt speed, the drive pulley force equals the sum of all resistances opposing belt motion around the conveyor loop.

2. Conveyor Resistances

ISO 5048 / DIN 22101 sum the main, secondary, special and slope resistances, and the Conveyor Equipment Manufacturers Association (CEMA) method sums the same losses as separate component terms. The table below groups these resistances by distribution, mechanical origin and governing dependencies, with the main resistance divided into its no-load and loaded parts.

Table 1: Conveyor Resistance Categories
Resistance Type Classification Description Mechanisms / Components Governing Dependencies
Empty running frictionMain resistance, no-loadDrag of the unladen belt and rotating idlers acting on both runs over the full centre-to-centre length.Idler bearing and seal friction. Belt flexure over idlers. Viscoelastic belt cover indentation.Friction factor f, conveyor length, belt mass, idler rotating mass.
Load frictionMain resistance, loadedAdditional drag from the conveyed material along the carrying run.Empty running mechanisms acting on the added material mass. Material and belt flexure between idlers.Material mass per unit length, friction factor f, conveyor length.
Slope resistanceLift or dropGravitational force component of material weight along the line of travel (belt weight forces cancel across runs).Positive work raising load (incline). Negative work lowering load (decline), requiring braking or regeneration where it exceeds the other resistances.Material mass per unit length, net elevation change (independent of length).
Secondary and special resistancesLocalised, or distributed over a defined sectionFriction and drag losses at discrete points or over defined sections, significant on short conveyors.Material acceleration at loading, skirtboard friction, belt cleaner drag, non-drive pulley resistance (belt wrap and bearing), forward-tilted idlers, discharge ploughs and trippers.Number and type of components, and length of skirted and tilted-idler sections.

3. Effective Tension and Power Calculation

Effective tension, T_e, is the net peripheral force required to drive or brake the loaded conveyor, equal to the sum of all resistances resolved at the drive pulley (F_U in ISO 5048).

Formula 1: Drive Pulley Power

Metric: P = T_e * v
Imperial: P = (T_e * v) / 33,000

Where:

  • P = Drive pulley power (kW) [hp]
  • T_e = Effective tension (kN) [lbf]
  • v = Belt speed (m/s) [fpm]
  • 33,000 = Conversion constant [ft-lbf/min per hp]

Engineering Takeaway: At a fixed mass flow, the load and lift components of effective tension vary inversely with belt speed, so their power demand is independent of speed, while empty running power rises in proportion to speed. Size the motor from P divided by the drive train efficiency, at the peak effective tension of the governing load case.

4. Belt Slip and the Euler-Eytelwein Equation

Transmitting the effective tension, without slip requires a minimum slack-side tension, T2, leaving the drive pulley. The Euler-Eytelwein (capstan) equation defines the maximum tension ratio before slip.

Formula 2: Euler-Eytelwein Slip Limit

T1 / T2 less than or equal to e^(mu * theta)

Where:

  • T1 = Tight-side tension entering the drive pulley (kN)
  • T2 = Slack-side tension leaving the drive pulley (kN)
  • mu = Friction coefficient between belt and pulley surface (dimensionless)
  • theta = Wrap angle of belt around the drive pulley (rad)
  • e = Base of the natural logarithm, 2.71828 (dimensionless)

Note: Convert theta to radians (deg * PI / 180).

Engineering Takeaway: The permissible tension ratio rises exponentially with mu * theta. Increase the wrap angle with a snub pulley or a dual-pulley drive, or the friction coefficient with lagging, to reduce the slack-side tension required for a given effective tension. This reduces total belt tension, the required belt rating and take-up mass.

Table 2: Friction Coefficients for Pulley Surfaces
Pulley Surface Dry Wet
Bare steel pulley0.25 to 0.300.10 to 0.15
Rubber lagging0.35 to 0.400.25 to 0.30
Rubber lagging (diamond-grooved)0.40 to 0.450.30 to 0.35
Rubber lagging (chevron/herringbone)0.40 to 0.450.30 to 0.35
Polyurethane lagging0.35 to 0.400.25 to 0.35
Polyurethane lagging (grooved)0.40 to 0.450.30 to 0.35
Ceramic lagging0.40 to 0.450.35 to 0.40
Ceramic lagging (dimpled)0.45 to 0.500.40 to 0.45
Ceramic lagging (rubber-backed composite)0.45 to 0.500.40 to 0.45
Direct-bonded ceramic (epoxy matrix)0.45 to 0.550.40 to 0.50
Slide-lagging (replaceable rubber pads)0.35 to 0.400.25 to 0.30

Note: Values are typical design values for clean conditions. Design with the lower bound of the wet range where the pulley runs wet or contaminated. Upper-range values for profiled and direct-bonded ceramic lagging are based on manufacturer data.

Formula 3: Minimum Slack-Side Tension

T2_min = T_e / (e^(mu * theta) - 1)

Where:

  • T2_min = Minimum slack-side tension to prevent slip (kN)
  • T_e = Effective tension, T1 - T2 (kN)
  • mu = Friction coefficient between belt and pulley surface (dimensionless)
  • theta = Wrap angle of belt around the drive pulley (rad)
  • e = Base of the natural logarithm, 2.71828 (dimensionless)

Note: Apply a slip safety factor of 1.2 or greater to T2_min and evaluate the worst case of a wet or cold pulley at peak starting and braking effective tension.

Engineering Takeaway: Set the take-up so that slack-side tension is not less than T2_min with the slip safety factor applied, and belt tension at the lowest-tension point of the carry and return runs is not less than the tension needed to hold the sag limit. On horizontal and low-lift conveyors the greater of the two sets the take-up force, and any excess slack-side tension adds directly to T1 and the required belt rating.

Formula 4: Drive Factor (C_w)

C_w = e^(mu * theta) / (e^(mu * theta) - 1)

Where:

  • C_w = Drive factor, the minimum ratio of tight-side tension to effective tension without slip (dimensionless)
  • mu = Friction coefficient between belt and pulley surface (dimensionless)
  • theta = Wrap angle of belt around the drive pulley (rad)
  • e = Base of the natural logarithm, 2.71828 (dimensionless)

Engineering Takeaway: The minimum tight-side tension is C_w * T_e. A higher friction coefficient or a larger wrap angle lowers C_w, and with it the tight-side tension and belt rating needed to transmit a given effective tension.

5. Drive and Take-Up Configurations

Drive and take-up locations determine the tension distribution around the belt loop. Correct placement minimises maximum belt tension and the required belt rating.

Table 3: Recommended Drive and Take-Up Locations
Conveyor Profile Drive Location Take-Up Location Basis Starting and Stopping Considerations
HorizontalHeadReturn side, immediately following the driveDrive slip typically governs. The take-up sets T2 directly at the drive slack side.The take-up absorbs elastic stretch during starting and stopping. Size take-up travel for the starting transient.
Incline, low liftHeadReturn side, immediately following the driveDrive slip governs. The take-up sets T2 directly at the drive slack side.Fit a holdback where the loaded belt can run back. Verify T2 at the drive during holdback engagement.
Incline, high liftHeadReturn side, at the tailCarry-side sag at the tail loading zone governs. Return belt weight raises tension from the tail to the drive, providing T2_min without additional take-up force.Fit a holdback. The starting tension wave reaches a tail take-up only after the wave transit time. Verify T2 at the drive during acceleration by dynamic analysis.
Decline (Regenerative)TailReturn side, immediately following the head pulleyThe tail drive retards the loaded carry strand on its tight side. Tension is lowest at the head pulley, where carry-side sag governs.Tension at the head falls during braking. Size the take-up to hold minimum tension and limit carry-side sag and spillage. Perform a dynamic analysis.
Multi-Slope (Undulating)Head, or as determined by the tension profileReturn side, at the minimum tension point for the governing load caseThe minimum tension point moves with the loading pattern on inclines and declines.Partial loading can shift the system between motoring and regenerating. Perform a dynamic analysis of transient slack waves.

Note: Locations apply to single-drive, non-reversing conveyors. Classify an incline as high lift where the carry-side sag tension at the tail, plus the return belt weight per metre multiplied by the lift, less the return run resistance, provides T2_min at the drive. Verify the carry-side sag tension at the minimum-tension point of the carry run.