1. Belt Capacities and Material Properties
Belt capacity is defined by volume, not mass. Size the belt so that the design capacity fills its full cross-section.
2. Factors Governing Belt Capacity
Operating close to the full cross-sectional profile maximises power efficiency (fixed belt, idler and drive losses spread across maximum payload) and improves tracking, as a centred load stabilises the belt. Belt capacity depends on four interrelated factors:
- Belt width and edge clearance: set by required capacity and material lump size.
- Belt speed: set by material characteristics (dustiness, abrasiveness, degradation) and loading and discharge arrangements.
- Idler configuration: troughing angle (20, 35 or 45 deg) and roll count (3, 4 or 5-roll).
- Material properties: bulk density, angle of repose and surcharge angle.
3. Properties of Bulk Materials
3.1 Angle of Repose versus Surcharge Angle
- Angle of repose: the angle a pile forms when material is deposited onto a stationary flat surface (static state).
- Surcharge angle: the angle material settles into while being vibrated and transported on a moving belt (dynamic state). It is typically 5 to 15 deg less than the angle of repose, and up to 20 deg less for some materials. Aerated powders exceed this offset.
3.2 Typical Material Values
Material density and angles vary with moisture content, lump size and cohesion. The table below gives typical values for commonly conveyed materials. Confirm design values by testing the specific material.
The maximum incline is typically 15 to 18 deg for dry bulk materials. Exceeding this limit induces material rollback. Free surface water lubricates the belt interface and reduces the allowable incline. Moisture without free surface water increases cohesion and can permit a steeper incline, as for damp sand. Inclines above 20 deg typically require moulded cleats, chevrons or corrugated sidewall belts.
| Material | Bulk Density kg/m3 [lb/ft3] | Angle of Repose deg | Surcharge Angle deg | Maximum Conveyor Incline deg |
|---|---|---|---|---|
| Alumina | 800 to 960 [50 to 60] | 22 | 5 | 12 |
| Bauxite (Crushed) | 1,200 to 1,360 [75 to 85] | 30 to 35 | 15 | 15 |
| Cement (Portland, Dry) | 1,200 to 1,360 [75 to 85] | 40 | 10 | 20 |
| Coal (Bituminous, Run-of-Mine (ROM)) | 720 to 880 [45 to 55] | 35 | 20 to 25 | 16 to 18 |
| Coal (Lignite/Brown) | 640 to 800 [40 to 50] | 35 | 25 | 18 |
| Coke (Screened) | 400 to 480 [25 to 30] | 30 | 25 | 15 |
| Earth (Dry, loose) | 1,120 to 1,280 [70 to 80] | 30 to 45 | 20 to 25 | 18 to 20 |
| Grains (Wheat/Corn) | 720 to 770 [45 to 48] | 28 | 10 | 12 to 14 |
| Gravel (Dry, sharp) | 1,440 to 1,600 [90 to 100] | 30 to 45 | 25 | 15 |
| Iron Ore (Crushed) | 2,200 to 2,900 [137 to 181] | 35 | 20 to 25 | 18 |
| Limestone (Crushed) | 1,280 to 1,440 [80 to 90] | 30 to 40 | 20 | 15 |
| Sand (Dry) | 1,440 to 1,600 [90 to 100] | 30 to 35 | 15 | 15 |
| Sand (Damp) | 1,600 to 2,080 [100 to 130] | 40 to 45 | 25 | 20 |
| Woodchips | 190 to 480 [12 to 30] | 45 | 25 | 23 to 25 |
Note: Underground drift conveyors handling ROM bituminous coal are typically inclined at 15 to 16 deg, incorporating a margin below the 18 deg limit to accommodate localised moisture or loading surges.
4. Maximum Lump Sizes and Particle Ratios
Maximum lump size, the largest a belt can carry without excessive spillage or carcass damage, depends on belt width and whether lumps are uniform or mixed with fines. Conveyor Equipment Manufacturers Association (CEMA) practice sets the following limits:
- Uniform lumps: For screened, predominantly uniform material (e.g. ballast rock), limit lump size to one fifth of belt width at a 20 deg surcharge angle, or one sixth at a 30 deg surcharge angle.
- Mixed lumps: For unscreened material such as ROM containing approximately 90% fines, lump size can reach one third of belt width. The fines cushion and bed the lumps into the profile centre, mitigating edge migration.
| Belt Width mm [in] | Uniform Lumps mm [in] | Mixed with Approximately 90% Fines mm [in] |
|---|---|---|
| 450 [18] | 90 [3.5] | 150 [6] |
| 600 [24] | 120 [5] | 200 [8] |
| 750 [30] | 150 [6] | 250 [10] |
| 900 [36] | 180 [7] | 300 [12] |
| 1,050 [42] | 210 [8.5] | 350 [14] |
| 1,200 [48] | 240 [10] | 400 [16] |
| 1,500 [60] | 300 [12] | 500 [20] |
| 1,800 [72] | 360 [14.5] | 600 [24] |
| 2,200 [87] | 440 [17.5] | 733 [29] |
Note: Values apply the one-fifth (uniform) and one-third (mixed) ratios at a 20 deg surcharge angle.
5. Typical Belt Speeds
Material degradation, dust generation and transfer chute geometry limit belt speed.
- Dusty materials: limit to 2.5 m/s [500 fpm] to reduce windage stripping of fines from the belt.
- Fragile materials: limit to 2.0 m/s [400 fpm] to minimise material degradation at transfer points (e.g. sized coal, wood pellets).
Overland conveyors handling ROM coal, copper or iron ore typically operate at 5.0 to 8.0 m/s [1,000 to 1,600 fpm]. These speeds require engineered transfer chutes (hood and spoon) to match material trajectory velocity to the receiving belt speed.
6. Volumetric Cross-Section and Edge Clearance
Material loaded onto a troughed belt forms a cross-section comprising a trapezoidal base (material within the trough) topped by a circular segment (the surcharge). Maintain an edge clearance, c, at each belt edge to limit spillage. DIN 22101 and CEMA define the minimum edge clearance for standard bulk materials.
Metric: c = 0.05 * B + 25
Imperial: c = 0.05 * B + 1.0
Where:
- c = Edge clearance at each belt edge (mm) [in]
- B = Belt width (mm) [in]
Note: The formula applies to belt widths up to 2,000 mm [79 in]. Above this width, DIN 22101 sets c at 125 mm [5 in].
The standard formulas assume a homogeneous, relatively fine bulk material. For large ROM lumps or primary crusher discharge, the standard edge clearance is often insufficient.
Large lumps do not flow as a homogeneous mass. They rest on the material profile and migrate toward the edges during idler transit. A lump whose dimension exceeds the edge clearance can roll off the belt edge.
For ROM and coarse lump material, increase the edge clearance above the standard value so that the wing idler slope contains lump migration. This reduces the usable volumetric capacity of the belt. Recalculate capacity with the increased clearance.
7. Effect of Troughing Angle on Capacity
The troughing idler angle dictates the cross-sectional area. Increasing the troughing angle from 20 deg to 35 or 45 deg increases volumetric capacity and can permit a narrower belt for the same throughput, reducing structural capital cost.
A 45 deg trough imposes higher bending stress at the idler junctions and requires a carcass rated for the trough angle. It also requires longer transition distances at the terminal pulleys to limit edge tension and fatigue. Deep troughing also restricts maximum lump size. Large lumps can wedge in the deep trough profile, jamming the loading chute or gouging the belt cover.
8. Capacity Calculations (Volumetric and Mass)
Define system capacity volumetrically, then convert to mass.
Metric: Q_v = 3600 * A * V
Imperial: Q_v = 60 * A * V
Where:
- Q_v = Volumetric capacity (m3/h) [ft3/h]
- A = Load cross-sectional area (m2) [ft2]
- V = Belt speed (m/s) [fpm]
Engineering Takeaway: Cross-sectional area is fixed once belt width, troughing angle and surcharge angle are set, leaving belt speed as the only variable that does not require structural change.
Metric: Q_m = 3.6 * A * V * rho
Imperial: Q_m = (A * V * rho * 60) / 2000
Where:
- Q_m = Mass capacity (t/h) [stph]
- A = Load cross-sectional area (m2) [ft2]
- V = Belt speed (m/s) [fpm]
- rho = Material bulk density (kg/m3) [lb/ft3]
Engineering Takeaway: Check volumetric capacity at the lowest expected bulk density, and drive power and structural loads at the highest.
On an incline, the gravity component along the belt reduces the effective surcharge angle and cross-sectional area. Multiply the horizontal capacity by the DIN 22101 incline reduction factor, k. A cosine correction understates the reduction.
k = 1 - (A_1 / A) * (1 - SQRT((COS(delta)^2 - COS(beta)^2) / (1 - COS(beta)^2)))
Where:
- k = Incline capacity reduction factor (dimensionless)
- A_1 = Surcharge (circular segment) area of the load cross-section on the horizontal (m2)
- A = Load cross-sectional area on the horizontal (m2)
- delta = Conveyor incline angle (deg)
- beta = Surcharge angle (deg)
Note: Valid for delta less than or equal to beta.
Engineering Takeaway: The reduction acts only on the surcharge area, which is lost entirely when delta equals beta. Materials with a low surcharge angle lose capacity at shallower inclines.
9. Design Capacity versus Nominal Capacity (Surge Handling)
Upstream flow is rarely uniform. Do not design a conveyor to operate continuously at 100% of calculated volumetric capacity.
Nominal capacity is the average feed rate required per operating hour.
Design (peak) capacity is the maximum surge rate the conveyor must handle without spillage or drivetrain overload. Design capacity is typically 115% to 125% of nominal capacity.
10. Factors Affecting Volumetric Capacity
The theoretical cross-sectional area is not achieved where conveyor geometry or material behaviour causes the load to shift or flatten. The following material properties and belt configurations reduce volumetric capacity.
| Material Type | Mechanism | Effect on Capacity |
|---|---|---|
| Aerated powders (fly ash, cement, dry alumina) | Fluidise during loading, resulting in a flattened profile. Surcharge angle drops to near 0 deg. | Volumetric capacity can be reduced by up to 50% relative to crushed rock. |
| High-moisture and slumping materials (wet tailings, saturated sand) | Slump toward the edges during transit vibration. | Derate the theoretical cross-sectional area to limit edge spillage. |
| Cohesive / sticky materials (sticky iron ore, wet loam) | Material adheres to the belt, increasing carryback. Hardened centre build-up reduces the effective trough geometry. | Carryback reduces effective mass throughput and usable cross-section. Primary and secondary cleaner drag increases motor power demand. |
| Free-flowing granular (dry sand, grain, screened gravel) | Low angle of repose. Settles to a shallow, stable profile and does not form a high surcharge. | Low surcharge angle (typically 5 to 15 deg) limits the surcharge area, restricting volumetric capacity relative to belt geometry. |
| Light / low-bulk-density materials (woodchips, bark, wood pellets) | High volume-to-mass ratio. System reaches volumetric capacity before reaching drivetrain or tension limits. | Capacity is volume-limited. Mass throughput is restricted at full cross-section. |
| Large lumps / ROM (primary crusher discharge, run-of-mine ore) | Migrate transversely during idler transit. Oversize lumps can wedge within high-trough-angle geometries. | Required edge clearance increases above the standard value, reducing usable cross-section. |
| Dusty / fine materials (fine coal, dry concentrate) | Aerodynamic drag (windage) induces dust emissions above the fines-retention velocity limit (typically 2.5 m/s [500 fpm]). | Belt speed is constrained to mitigate emissions, limiting maximum mass throughput. |
| Fragile / degradable materials (sized coal, wood pellets, lump ore) | Impact at transfer points generates fines and alters the particle size distribution. | Belt speed limited to approximately 2.0 m/s [400 fpm] to control degradation, capping throughput. |
Note: The 50% reduction is calculated from DIN 22101 cross-section geometry for a 1,200 mm [48 in] belt on 20 deg three-roll idlers, with the surcharge angle reduced from 25 deg to 0 deg. On 35 deg idlers, the same change reduces capacity by approximately 37%.
| Factor | Mechanism | Impact on Capacity |
|---|---|---|
| Horizontal curves | Banked (tilted) idlers shift the material centroid toward the outer radius. | Derate volumetric capacity and increase edge clearances to limit outer-radius spillage. |
| Convex vertical curves (crests) | High edge tension at the crest flattens the belt profile across the wing idlers, expanding the material base width. | A belt operating at 100% capacity on horizontal sections may spill during convex transitions. |
| Concave vertical curves (valleys) | Belt lift-off occurs if the tension-to-load ratio is excessive, disrupting the material profile. | Profile disturbance increases spillage risk. Derate volumetric capacity through the curve. |
| Incline | The gravity component along the belt reduces the effective surcharge angle. | Cross-sectional area decreases. Reduction is approximately 5% at 10 deg and 10% at 15 deg. |
| Wide idler spacing (trampoline effect) | Belt sag between idlers induces profile pinching, followed by flattening over the roll. Repeated cycling drives transverse material migration. | Sag exceeding 2% of idler spacing induces progressive material migration, risking localised spillage between idler frames. |
Note: Incline reductions are typical published factors for troughed belts and vary with surcharge angle.
11. Increasing Capacity by Belt Speed
Where mass capacity must increase on a conveyor already at full volumetric capacity, a wider belt is the direct solution, but the structural replacement is frequently capital-prohibitive. Increasing belt speed by gear ratio change or variable frequency drive (VFD) raises mass throughput at constant cross-section. Verify each component in the table below before modification.
| Component | Mechanism | Consequence | Check Required |
|---|---|---|---|
| Idler Bearing Basic Rating Life (L10h) | Idler rotational speed increases in proportion to belt speed. | L10h varies inversely with rotational speed. At constant cross-section, bearing load is unchanged, so L10h falls in inverse proportion to belt speed. | Recalculate L10h at the new rotational speed and load against target life. |
| Material Trajectory and Transfer Chutes | Higher discharge velocity lengthens the material trajectory. | Trajectory overshoot can bypass impact beds and rock boxes, leading to direct impingement on chute walls and accelerated wear. | Recalculate and plot the trajectory. Verify compatibility with existing chute and impact bed geometry. |
| Motor and Drivetrain (Power Limits) | Power equals effective tension multiplied by belt speed. Higher speed and throughput raise power demand. | Existing motors and drive components may exceed their thermal or mechanical ratings. Above motor base speed, a VFD-driven motor operates at constant power and available torque falls in inverse proportion to speed. | Verify power ratings and torque capacities of motors, reducers, fluid couplings and drive pulley shafts. |
| Aeration and Windage | Aerodynamic drag increases with speed and becomes significant above 3.0 to 4.0 m/s [600 to 800 fpm]. For dust-sensitive fines, the retention limit is typically 2.5 m/s [500 fpm]. | Elevated speeds induce windage, stripping fines from the material profile and increasing fugitive dust emissions. | Evaluate fines content and verify the capacity of existing dust suppression and extraction systems at the higher speed. |
| Skirtboard Wear | Material requires a longer distance to settle and accelerate to belt speed. Skirtboard friction power and wear increase linearly with belt speed. | Existing skirtboard length may be insufficient to contain the turbulent profile. Liner wear rates increase. | Verify skirtboard length against the required settling distance. Recalculate wear liner maintenance intervals. |