1. Conveyor Belts and Grades
A conveyor belt comprises a carcass, which carries the operating tensions, absorbs impact and supports the load, and rubber or polyvinyl chloride (PVC) covers, which protect the carcass from abrasion, impact, heat, oil and chemical damage. Specify the carcass first for tension and load support, then select the cover for environmental and wear resistance.
2. Belt Constructions
The conveyor belt industry uses three predominant carcass constructions: multi-ply fabric (polyester/nylon EP or PN, nylon/nylon NN and polyester/polyester EE), solid woven (SW) and steel cord (ST). Each has distinct mechanical properties, splicing requirements and application domains.
| Characteristic | Multi-Ply Fabric (EP/PN, NN, EE) | Solid Woven (SW) | Steel Cord (ST) |
|---|---|---|---|
| Carcass Construction | Multiple discrete woven textile plies bonded with inter-ply skim coat rubber | Single interlocked weave of synthetic fibres fully impregnated with PVC | Single layer of evenly spaced zinc-galvanised high-tensile steel wire ropes in bonding rubber matrix |
| Strength Range kN/m [PIW] | 315 to 2,500 [1,800 to 14,300] | 500 to 3,150 [2,850 to 18,000] | 500 to 10,000 [2,850 to 57,100] |
| Elongation (Stretch) | 1.0% to 2.0% | Less than 1.0% | Less than 0.25% |
| Delamination Risk | Yes (plies can separate) | No (single interlocked matrix) | No (single cord layer) |
| Mechanical Fasteners | Acceptable (with tension reduction) | Excellent retention | Unsuitable |
| Splicing | Vulcanised or mechanical | Vulcanised or mechanical | Vulcanised only |
| Primary Application | General above-ground bulk handling (predominant construction) | Underground coal and potash mining, enclosed high-hazard sites | Long overland and high-tension conveyors, sites with limited take-up travel |
| Cover Material | Rubber: natural rubber (NR), styrene-butadiene rubber (SBR), ethylene propylene diene monomer (EPDM), nitrile butadiene rubber (NBR) and polychloroprene (CR) | PVC or thin rubber | Rubber (NR, SBR, CR) |
| Temperature Sensitivity | Moderate (rubber-dependent) | High (PVC softens above 70 deg C [158 deg F]) | Low (rubber-dependent) |
| Key Advantage | Versatile, wide tension range, accepts both joint methods | Cannot delaminate. Fire resistant and anti-static. Retains mechanical fasteners. | Minimal elongation and high splice efficiency. Highest tension ratings available. |
Note: Strength values are ultimate breaking strength. PIW denotes pounds-force per inch of belt width (lbf/in).
3. Carcass Reinforcements
The table below lists common carcass reinforcements. Fabric designations state the warp (longitudinal) material first and the weft (transverse) material second, e.g. PN (or EP) denotes a polyester warp and nylon weft.
| Carcass Type | Warp (Longitudinal) | Weft (Transverse) | Ultimate Strength Range kN/m [PIW] | Features, Applications and Rules of Thumb |
|---|---|---|---|---|
| PN / EP (Plain Weave) | Polyester | Nylon | 315 to 1,600 [1,800 to 9,100] | Standard construction. Low elongation (typically less than 1.5%), good impact resistance, excellent fastener holding. General purpose. |
| PN / EP (Crow's Foot Weave) | Polyester | Nylon | 630 to 2,500 [3,600 to 14,300] | High rip and tear resistance due to interlocking weave. Suitable for heavy-duty applications, large lump sizes and primary crushers. |
| Straight Warp | Polyester or Nylon | Nylon | Up to 3,150 [Up to 18,000] | Heavy longitudinal cords held straight (no crimp), bound by transverse cords. High impact and rip resistance. Often used in 1- or 2-ply high-tension constructions. |
| NN (Plain Weave) | Nylon | Nylon | Up to 2,000 [Up to 11,400] | High elongation. Largely superseded by PN/EP, but still used where increased flexibility, low modulus or high pH resistance is needed. |
| EE (Plain Weave) | Polyester | Polyester | Up to 900 [Up to 5,100] | Used in special applications where high acid resistance is needed. Poor transverse flexibility compared to PN/EP. |
| Solid Woven (SW) | Nylon/Cotton or Polyester/Cotton | Nylon/Cotton | 500 to 3,150 [2,850 to 18,000] | Main use in underground coal mining. Interlocked weave has no plies to separate. Resistant to moisture when PVC impregnated. High retention for mechanical fasteners. |
| Steel Cord (ST) | Steel Wire Rope | None (Standard) | 500 to 10,000 [2,850 to 57,100] | Minimal elongation (less than 0.25%). Used for long overland conveyors and high-tension applications. Vulcanised splicing only. Transverse steel breakers can be added for rip protection. |
| Aramid | Aramid | Nylon | 630 to 3,150 [3,600 to 18,000] | Low elongation, high strength, low weight. Suitable alternative to steel cord where magnetic properties, belt mass or corrosion are constraints. |
3.1 Warp-to-Weft Strength Ratio
Warp (longitudinal) yarns carry operating tension and weft (transverse) yarns provide lateral stability, impact distribution and fastener retention. Weft strength is typically 10% to 25% of warp strength.
A lump striking the belt at 90 deg is absorbed primarily by the weft yarns. Insufficient weft strength causes impact breakthrough and longitudinal splitting between the warp cords. Standard catalogue weft strengths suit general service. For heavy, sharp lumps under high-impact loading or for belts with mechanical fasteners under high tension, specify a high-weft or reinforced-weft construction.
4. Belt Carcass Selection
Carcass selection balances flexibility against rigidity. The belt requires sufficient tensile strength to carry the operating tension, adequate transverse rigidity to support material across the idler junctions, sufficient transverse flexibility to conform to the trough and adequate longitudinal flexibility to wrap the pulleys.
Evaluate five criteria to select the carcass:
- Belt Width: Dictated by capacity and lump size.
- Maximum Operating Tension (T_max): The highest steady-state tension in the system.
- Peak Tensions: Transient tensions during starting (acceleration) and stopping (braking).
- Load Support (Minimum Plies/Thickness): The minimum carcass stiffness required to support the load across the idler junctions without creasing.
- Troughability (Maximum Plies/Thickness): The maximum carcass stiffness allowed before the belt becomes too rigid to conform to the trough profile.
4.1 Regional Designations: CEMA versus ISO / DIN
Establish the applicable regional strength designation, Conveyor Equipment Manufacturers Association (CEMA) or ISO / DIN, before carcass selection.
| Designation System | Region | Rating Basis | Units | Example | Safety Factor |
|---|---|---|---|---|---|
| Imperial / CEMA | North America | Allowable Working Tension | PIW (lbf per inch of width) | 3-ply 330 PIW: 3 plies, allowable working tension of 58 kN/m [330 PIW] | 10:1 (breaking strength approximately 10 times working) |
| Metric (AS / ISO / DIN) | Australia, Europe and global | Ultimate breaking strength and ply count | kN/m | EP 630/3 (ISO / DIN) or PN 630/3 (AS): 630 kN/m [3,600 PIW] ultimate, 3 plies polyester/nylon. Safe working tension approximately 63 kN/m [360 PIW]. | 10:1, applied separately (safe working approximately 1/10 of ultimate) |
Multiply a tension in kN/m by 5.71 to obtain PIW. This conversion changes only the units and applies no safety factor. Because 1 kN/m equals 1 N/mm, the same factor converts N/mm to lbf/in. To obtain a safe working tension from a metric belt's ultimate strength, apply the safety factor as a separate step.
T_s = (5.71 * S_u) / SF
Where:
- T_s = Safe working tension (PIW)
- S_u = Ultimate breaking strength (kN/m)
- SF = Safety factor (dimensionless)
Note: With a 10:1 safety factor, the formula reduces to T_s = S_u / 1.75, since 10 / 5.71 = 1.7513. The 1.75 constant is valid only for a 10:1 safety factor. For steel cord belting at 6.7:1, the constant becomes 6.7 / 5.71 = 1.173. Recalculate the constant for any other safety factor.
Engineering Takeaway: A constant derived for one safety factor misstates the safe working tension at any other. Applying the steel cord constant of 1.173 to a fabric belt rated at 10:1 overstates its safe working tension by approximately 49%.
4.2 Starting and Braking Tensions
Evaluate acceleration and braking tension against the allowable peak tension of the belt.
- Standard Conditions: Limit peak tension on starting or braking to 140% of the allowable steady-state working tension.
- Severe Conditions: For short cycle times, frequent loaded Direct-On-Line (DOL) starts or heavy impact, reduce the rated vulcanised working tension by 15%. For mechanical fasteners, the reduction applies to the already-reduced fastened rating. Limit peak tension to 150% of this reduced rating.
- Extreme Conditions: For poor maintenance, high-temperature materials or chemically aggressive environments, reduce the rated vulcanised working tension by 30%, on the same basis for mechanical fasteners. Limit peak tension to 160% of this reduced rating.
4.3 Mechanical Fasteners versus Vulcanised Splices
Standard practice specifies hot or cold vulcanised splices for plain weave plied belting. A stepped splice in an n-ply belt has a theoretical efficiency of (n - 1) / n of the belt strength, e.g. 67% for 3-ply and 75% for 4-ply. Single-ply straight-warp or aramid belts require specialised finger splicing. Standard stepped splices on these materials can reduce splice efficiency to below 50%.
Where mechanical fasteners (hinged clips or solid plate) are used, derate the allowable working tension for fastener stress concentration, typically by 20% to 25% on standard EP fabric relative to a vulcanised splice. Solid Woven (PVC) belts offer superior fastener retention owing to their interlocking weave.
4.4 Troughability and Load Support Mechanics
Transverse rigidity sets upper and lower limits on the ply count for a given belt width.
- Troughability limit (excessive transverse rigidity): Excessive ply counts for a given belt width prevent the carcass from conforming to the trough profile. During empty operation, the belt spans the wing idlers without centre roll contact, resulting in erratic tracking and potential edge damage.
- Load support limit (insufficient transverse rigidity): Insufficient ply counts allow high-density material to force the carcass into the idler junctions. This induces longitudinal creasing, progressive carcass fatigue and splitting.
4.5 Carcass Selection Procedure
Calculate the required unit working tension:
T_w = T_max / B
Where:
- T_w = Required unit working tension (kN/m)
- T_max = Maximum steady-state belt tension (kN)
- B = Belt width (m)
Engineering Takeaway: Required unit working tension is the primary input to the carcass rating. Widening the belt for capacity lowers the unit working tension but can exceed the load-support limit for the resulting lower ply count.
Then proceed through the remaining checks:
- Determine the splicing method. Where mechanical fasteners are used, divide unit working tension by 0.75 before comparing it with the vulcanised rating, or compare unit working tension directly with the fastened rating.
- Select a carcass with an allowable working tension equal to or greater than unit working tension.
- Check troughability. Confirm the belt width equals or exceeds the minimum width required to trough the selected ply count.
- Check load support. Confirm the belt width does not exceed the maximum width for the bulk density of the material.
- Check pulley diameters. Confirm the installed pulley diameters meet the minimum diameters for the selected carcass.
4.6 Standard Carcass Selection Tables
| ISO Designation (Ultimate Strength) | Maximum Working Tension, Vulcanised kN/m [PIW] | Maximum Working Tension, Fastened kN/m [PIW] |
|---|---|---|
| EP 315 / 2-ply | 31.5 [180] | 23.6 [135] |
| EP 400 / 2-ply | 40.0 [228] | 30.0 [171] |
| EP 500 / 3-ply | 50.0 [286] | 37.5 [214] |
| EP 630 / 3-ply | 63.0 [360] | 47.3 [270] |
| EP 800 / 4-ply | 80.0 [457] | 60.0 [343] |
| EP 1000 / 4-ply | 100.0 [571] | 75.0 [428] |
| EP 1250 / 5-ply | 125.0 [714] | Not Recommended |
| EP 1600 / 5-ply | 160.0 [914] | Not Recommended |
| EP 2000 / 5-ply (Crow's Foot) | 200.0 [1,140] | Not Recommended |
| EP 2500 / 5-ply (Crow’s Foot) | 250.0 [1,430] | Not Recommended |
Note: Values apply only to Standard Conditions. Vulcanised splice values assume a standard 10:1 safety factor applied to the belt's ultimate breaking strength. Fastened values reduce the vulcanised working tension by 25% for fastener stress concentration, giving an effective safety factor of approximately 13.3:1. EP 2000 and EP 2500 ratings are typically achieved using crow's foot weave or straight-warp constructions. Plain weave EP fabric is not generally manufactured above EP 1600. Mechanical fasteners are not recommended above EP 1000 due to the high stress concentrations at the fastener bar relative to the belt tension.
The table below gives the minimum belt width for empty-belt contact with the centre roll.
| Number of Plies | 20 deg Trough mm [in] | 35 deg Trough mm [in] | 45 deg Trough mm [in] |
|---|---|---|---|
| 2-Ply | 400 [16] | 450 [18] | 500 [20] |
| 3-Ply | 450 [18] | 500 [20] | 600 [24] |
| 4-Ply | 600 [24] | 750 [30] | 900 [36] |
| 5-Ply | 750 [30] | 900 [36] | 1,050 [42] |
| 6-Ply | 900 [36] | 1,050 [42] | 1,200 [48] |
The table below gives the maximum belt width before the load forces the carcass into the idler junctions, based on a 35 deg trough.
| Number of Plies | Light Material, Less Than 800 kg/m3 [50 lb/ft3], mm [in] | Heavy Material, Greater Than 1,600 kg/m3 [100 lb/ft3], mm [in] |
|---|---|---|
| 2-Ply | 1,000 [40] | 750 [30] |
| 3-Ply | 1,350 [54] | 1,050 [42] |
| 4-Ply | 1,800 [72] | 1,350 [54] |
| 5-Ply | 2,200 [87] | 1,800 [72] |
| 6-Ply | 2,400 [96] | 2,000 [79] |
Note: Where capacity requires a belt wider than the load-support limit for the tension-governed ply count, increase the ply count or fabric weight to achieve the required transverse stiffness, even where the additional tension rating is not required. For bulk densities between 800 and 1,600 kg/m3 [50 and 100 lb/ft3], use the heavy material limit or confirm with the belt manufacturer.
5. General Properties of Belt Covers and Grades
Compounding modifies baseline polymer properties. The cover grade defines the minimum tensile, elongation and abrasion properties of the compound and its resistance to heat, oil and fire.
5.1 Cover Performance Standards and Testing
Belt cover physical properties are verified by laboratory testing.
- Tensile Strength: Stress at rupture of the cover rubber, in MPa. Minimum values range from 15 to 25 MPa [2,200 to 3,600 psi] for general service grades (AS 1332 / ISO 10247 / DIN 22102). Higher tensile strength correlates with improved cut and gouge resistance.
- Elongation at Break: Strain at rupture, typically 300% to 450% for standard NR/SBR grades, and an indicator of impact absorption without cracking. Low elongation (below 300%) indicates a hard, brittle compound that spalls and fractures under severe lump impact.
- Abrasion Resistance (Volume Loss): Measured per ISO 4649 (formerly DIN 53516) by pressing a sample against a rotating abrasive drum and measuring volume lost in mm3. This is a primary comparative metric for cover selection. A lower volume loss correlates with higher abrasion resistance. Legacy DIN 53516 values are comparable and may be read directly against ISO 4649 thresholds.
| Cover Grade (AS / DIN / RMA) | Maximum Abrasion Volume Loss (ISO 4649) mm3 | Application Guidance |
|---|---|---|
| Grade N / DIN Y (RMA Grade II) | 200 (Grade N), 150 (DIN Y) | Standard general purpose. Coal, sand and gravel. |
| Grade M / DIN X (RMA Grade I) | 125 (Grade M), 120 (DIN X) | Multi-purpose grade. Improved abrasion resistance compared to Grade N / Y, with enhanced cut, impact and gouge resistance. Primary crusher discharge, run-of-mine (ROM) rock, large sharp lumps. |
| Grade A (SAR) / DIN W | 70 (Grade A), 90 (DIN W) | Super abrasion resistant (SAR) grade with the highest abrasion resistance of the standard grades. Iron ore fines, glass cullet, fine sliding-abrasive materials. Not optimised for impact or gouging. |
| Grade S (AS 1332) | 250 | Fire resistant anti-static (FRAS) grade for underground and enclosed use (AS 4606), typically CR or CR-SBR based. Abrasion performance is secondary to fire compliance. |
| DIN Grade K (Fire Resistant) | 200 | Fire-retardant and anti-static compound per DIN 22102. Abrasion resistance is lower than DIN Grades W, X and Y. |
| Heat Resistant (SBR / EPDM) | 200 (typical) | Heat resistance is achieved at the expense of abrasion resistance. |
| Oil Resistant (NBR) | 150 (typical) | Moderate abrasion resistance. Oil resistance is the primary driver. |
Note: RMA denotes the former Rubber Manufacturers Association grade system, which sets no abrasion limit. Abrasion volume loss is reported in mm3 under ISO 4649 and is not converted.
Volume loss below 100 mm3 indicates high abrasion resistance. Specialty compounds (heat, oil or fire resistant) typically range from 150 to 250 mm3, as chemical or fire performance takes precedence over wear life. Do not select heat- or oil-resistant covers on abrasion performance alone.
The DIN grades W, X and Y do not form a linear hierarchy. Grade Y (150 mm3 maximum) functions as the standard baseline. Grade W (90 mm3 maximum) is formulated for sliding-wear resistance and exhibits lower performance under heavy impact or gouging. Grade X (120 mm3 maximum) provides above-baseline abrasion resistance alongside enhanced cut, impact and gouge resistance.
Cover Hardness (Shore A Durometer) is typically 55 to 65 Shore A for general service grades. Harder compounds (65 to 75 Shore A) resist abrasive cutting but chip more readily under impact. Softer compounds (50 to 58 Shore A) absorb impact better but wear faster under sliding abrasion. Retain the manufacturer's standard hardness for the selected grade unless the duty requires otherwise.
5.2 Cover-to-Carcass Adhesion
Cover delamination causes premature carcass failure irrespective of initial cover thickness.
Adhesion values near the specified minimum on a test certificate can indicate substandard calendering or contaminated resorcinol-formaldehyde-latex (RFL) treatment. Specify adhesion 25% to 50% above the minimum values. Low field adhesion manifests as blistering or delamination, especially in hot, humid or chemically aggressive environments. For steel cord belts, the equivalent metric is cord pull-out strength.
The table below gives minimum adhesion values for fabric belts. Cover-to-ply limits depend on cover thickness.
| Adhesion Type | AS 1332 N/mm [lbf/in] | DIN 22102 N/mm [lbf/in] | Test Standard |
|---|---|---|---|
| Ply-to-Ply (fabric belts) | 6.0 [34.3] | 5.0 [28.6] | ISO 252 |
| Cover-to-Ply, thin covers (up to 1.9 mm [0.075 in] AS, up to 1.5 mm [0.06 in] DIN) | 4.0 [22.8] | 3.5 [20.0] | ISO 252 |
| Cover-to-Ply, thicker covers | 4.8 [27.4] | 4.5 [25.7] | ISO 252 |
Note: For steel cord belts, cord pull-out strength and cover-to-cord adhesion are specified per ST rating in AS 1333 and ISO 15236-1 (formerly DIN 22131) and tested to ISO 7623. Obtain the values for the selected ST rating from the standard or the belt manufacturer.
5.3 Static Conductivity and Anti-Static Requirements
The electrical resistance of a belt dictates whether it can safely dissipate static charges built up by friction against idlers and pulleys. Static discharge in environments containing combustible bulk materials constitutes an explosion hazard.
AS 1334.9 / ISO 284 measures surface resistance between electrodes on each cover surface. For standard anti-static service, surface resistance must be less than 300 MOhm (the general requirement for above-ground bulk handling). For FRAS (underground or hazardous) service, the belt must meet regional fire and static standards (AS 4606, EN 14973, Mine Safety and Health Administration (MSHA) Part 14). AS 4606 and EN 14973 mandate low surface resistance, gallery fire tests for propagation resistance and drum friction tests, which simulate a stalled belt on a running drive pulley. MSHA Part 14 mandates flame tests only.
Under AS 4606, resistance must be verified independently on both top and bottom covers. This is particularly relevant for Grade S belts, where the two covers may use different rubber formulations (for example a thicker, abrasion-resistant top cover and a thinner, higher-friction bottom cover). Confirm that both surfaces are independently certified.
Standard NR/SBR compounds are typically semi-conductive owing to their carbon black filler. Oil-resistant NBR and heat-resistant EPDM compounds are not inherently anti-static. The DIN Grade K definition includes anti-static performance to ISO 284. Where NBR or EPDM is specified for a combustible-dust environment, add an explicit anti-static requirement (surface resistance less than 300 MOhm per AS 1334.9 / ISO 284 / DIN 22104) to the purchase specification and confirm it on the test certificate.
5.4 General Service Cover Grades
| Property | Natural Rubber (NR) / SBR | Natural Rubber (NR) | Polybutadiene (NR/BR) | Natural Rubber Blend (NR/SBR) |
|---|---|---|---|---|
| Polymer Base / Chemistry | NR/SBR blend, carbon-black reinforced, sulphur-cured. SBR added for wear and weather resistance, NR for resilience. | High natural rubber (cis-1,4-polyisoprene), heavily carbon-black loaded, high-resilience sulphur cure. | NR/BR (polybutadiene) blend. BR raises abrasion resistance and low-temperature flexibility. | NR-dominant with SBR toughening, high carbon-black loading, optimised for tear and gouge resistance over wear. |
| Application | Medium to heavy duty bulk handling (coal, sand) | Heavy to extreme mining service with large lumps and high impact | High abrasion resistance for fine, sharp, sliding-abrasive materials (glass cullet, iron ore fines). Not for high impact. | Cut and gouge resistant for extreme heavy service (primary rock) |
| AS 1332 / DIN Grade | Grade N / DIN Y (RMA II) | Grade M / DIN X (RMA I) | Grade A (SAR) / DIN W | No standard grade (manufacturer cut and gouge grade) |
| Minimum Tensile Strength MPa [psi] | 17 [2,500] (Grade N) / 20 [2,900] (DIN Y) | 24 [3,500] (Grade M) / 25 [3,600] (DIN X) | 17 [2,500] (Grade A) / 18 [2,600] (DIN W) | 24 [3,500] |
| Minimum Elongation at Break % | 400 | 450 | 400 | 400 |
| Maximum Abrasion Volume Loss (ISO 4649) mm3 | 200 (Grade N) / 150 (DIN Y) | 125 (Grade M) / 120 (DIN X) | 70 (Grade A) / 90 (DIN W) | 100 |
| Friction Coefficient (Drive) | Good | Good | Good | Good |
| Weather/Ozone Resistance | Good | Good | Good | Very good |
| Cut/Tear Resistance | Good to excellent | Good to excellent | Good | Excellent (gouge resistant) |
| Abrasion Resistance | Good to very good | Very good (combined abrasion, cut and impact) | Excellent (sliding abrasion) | Very good |
| Service Temperature Range deg C [deg F] | minus 30 to 70 [minus 22 to 158] | minus 30 to 70 [minus 22 to 158] | minus 30 to 70 [minus 22 to 158] | minus 30 to 70 [minus 22 to 158] |
Note: Values in the NR/SBR blend (cut and gouge) column are typical manufacturer values. All other strength, elongation and abrasion values are specification limits.
5.5 Heat Resistant Cover Grades
Thermal degradation mechanisms vary by material size: fine powders trap heat against the cover, causing hardening and cracking, whereas coarse materials permit air circulation but cause localised thermal degradation. Select the elastomer to suit the degradation mechanism.
| Property | Heat Resistant Standard (SBR) | Heat Resistant Fines (EPDM) | Heat Resistant Maximum (Ethylene Propylene Rubber, EPR/EPDM) | Heat Resistant Anti-Crack (Chlorobutyl, CIIR) |
|---|---|---|---|---|
| Polymer Base / Chemistry | Styrene-butadiene copolymer, heat-stabilised sulphur or semi-EV cure, high antioxidant and antiozonant loading for thermal ageing resistance | Ethylene propylene diene monomer, peroxide-cured saturated backbone. No main-chain double bonds, so resistant to thermal oxidation and hardening. | High-ethylene EPDM/EPR, peroxide-cured, heat-stabiliser package for high-temperature service | Chlorobutyl (chlorinated isobutylene-isoprene), low gas permeability and high resistance to oxidative cracking |
| Application | Heat resistant for coarse and abrasive materials (slag) | Heat resistant for fine materials. Resists hardening and cracking. | Maximum heat resistance for fine materials (cement, foundry sand) | Extreme heat, highly resistant to cracking and oxidation |
| Abrasion Resistance | Very good | Good | Good | Fair |
| Maximum Continuous Service Temperature deg C [deg F] | 125 [257] | 170 [338] | 210 [410] | 200 [392] |
| Peak Temperature Limit, Short Term deg C [deg F] | 150 [302] | 200 [392] | 400 [752] (with cooling) | 250 [482] |
Heat accelerates degradation of the cover-to-carcass bond. Above a sustained 120 deg C [248 deg F], standard cover-to-carcass bonding systems lose adhesion. For continuous operation above 150 deg C [302 deg F], confirm the heat-stable adhesion system with the manufacturer, typically modified phenolic or resorcinol-based bonding agents between the EPDM cover and polyester carcass.
Material temperature differs from belt cover temperature. Peak thermal exposure occurs transiently at the loading zone, and the belt cover temperature is lower than the peak material temperature by an amount that depends on cycle time, bed depth and contact duration. A belt carrying 200 deg C [392 deg F] clinker therefore does not necessarily require a 200 deg C [392 deg F] rated compound if the cycle time is long and the material bed thin.
5.6 Oil and Chemical Resistant Cover Grades
Oil swells natural rubber covers, causing blistering and cover separation from the carcass. Terpenes (found in woodchips) and vegetable and animal oils (grain, fertiliser) require moderate oil resistance (MOR), whereas mineral oils (treated coal, petroleum coke) require nitrile-based super oil resistance (SOR).
| Property | Nitrile Rubber (NBR) | Polychloroprene (CR) | Nitrile PVC (NBR / PVC) | Nitrile Blend (NBR/SBR) |
|---|---|---|---|---|
| Application | Maximum oil resistance. Petroleum, treated coal, machine parts. | Oil and flame resistant | Grain handling, fertiliser, elevator belts | Moderate oil resistance. Woodchips, waste recycling. |
| Abrasion Resistance | Very good | Good | Very good | Good |
| Mineral/Petroleum Oils | Excellent | Very good | Very good | Good |
| Vegetable/Animal Oils | Excellent | Good | Excellent | Excellent |
| Service Temperature Range deg C [deg F] | minus 10 to 125 [14 to 257] | minus 10 to 110 [14 to 230] | minus 10 to 120 [14 to 248] | minus 20 to 70 [minus 4 to 158] |
Where chemical compatibility is uncertain, specify a manufacturer immersion swell test (ISO 1817 / ASTM D471), in which a rubber sample is immersed in the actual process oil or chemical at the operating temperature for 72 h. Limit volume swell to less than 20%. Swell exceeding 30% causes cover delamination in service.
5.7 Fire Resistant and Anti-Static Cover Grades
Regional regulations dictate the use of these belts. Underground operations usually require self-extinguishing properties with gallery fire tests: AS 4606 (Australia), EN 14973 (Europe) and MSHA Part 14 (USA).
| Property | Polychloroprene (CR) | AS Grade S (CR / CR-SBR Blend) | DIN Grade K (CR or SBR base) | SBR/Polybutadiene Blend | PVC (Solid Woven) |
|---|---|---|---|---|---|
| Application | Underground coal, enclosed hazardous environments (grain silos) | Underground coal and hard-rock mining, port terminals, grain silos. For plied rubber covered belting (EP/PN carcass) requiring AS 4606 underground certification. | Above-ground enclosed handling through to underground mining, depending on certification path. Applied to EP/PN, NN or steel cord carcasses. | Above-ground coal handling, power plants and port terminals | Underground coal mining |
| Fire Certification Path | AS 4606 / MSHA Part 14 | AS 4606 (underground) | ISO 340 (above-ground) or EN 14973 (underground) | ISO 340 / MSHA 2G | AS 4606 / MSHA Part 14 |
| Flame Resistance | Excellent (self-extinguishing) | Excellent (self-extinguishing) | Self-extinguishing under EN 14973. Fire-retardant only under ISO 340. | Good (fire retardant) | Excellent |
| Anti-Static | Yes (less than 300 MOhm) | Yes (less than 300 MOhm, both surfaces per AS 4606) | Yes (less than 300 MOhm per ISO 284, included in the grade definition) | Yes (less than 300 MOhm) | Yes |
| Abrasion Resistance | Good to very good | Fair (250 mm3 maximum) | Good (200 mm3 maximum, DIN 22102) | Very good | Good |
| Minimum Tensile Strength MPa [psi] | 15 [2,200] | 14 [2,000] | 20 [2,900] (DIN 22102) | 15 [2,200] | Not applicable (PVC matrix) |
| Minimum Elongation at Break % | 300 | 300 | 400 (DIN 22102) | 350 | Not applicable |
| Hardness (Shore A) | 55 to 65 | 55 to 65 | 55 to 70 | 55 to 65 | 75 to 85 |
| Service Temperature Range deg C [deg F] | minus 10 to 110 [14 to 230] | minus 10 to 110 [14 to 230] | minus 10 to 110 [14 to 230] (CR base). Minus 30 to 70 [minus 22 to 158] (SBR base). | minus 30 to 70 [minus 22 to 158] | minus 15 to 70 [5 to 158] (to minus 40 [minus 40] with cold-weather plastisol) |
| Typical Carcass Pairing | Multi-ply EP/PN or Solid Woven | Multi-ply EP/PN (plied rubber-covered belting) | Multi-ply EP/PN, NN or steel cord (ST) | Multi-ply EP/PN | Solid woven (interlocked weave, PVC impregnated) |
Two textile constructions are commonly certified to AS 4606 for Australian underground coal mining. Solid Woven PVC is a single-matrix PVC-impregnated interlocked carcass with PVC or thin rubber covers. It resists delamination, retains mechanical fasteners and is common practice for development conveyors that are frequently cut, shortened and re-fastened. Grade S plied rubber is a standard multi-ply EP/PN carcass with Grade S FRAS covers. It provides higher abrasion resistance and drive friction than PVC and accepts vulcanised splices for higher joint strength. Selection depends on how frequently the conveyor length changes. For longwall gate roads and continuous miner development panels, where the belt is cut and rejoined repeatedly, specify Solid Woven PVC with mechanical fasteners. For a fixed-length main trunk or drift conveyor spliced once and operated for years, specify Grade S plied rubber for its wear life, drive friction and splice efficiency.
PVC covers have a lower coefficient of friction than rubber, so a Solid Woven PVC belt on a standard rubber-lagged drive pulley may slip under high tension or in wet conditions where Grade S would not. Where Solid Woven PVC is specified for a high-tension underground trunk conveyor, specify ceramic drive pulley lagging.
DIN Grade K and AS Grade S are comparable fire-resistant compound designations with different minimum specification limits. At the specification limits, DIN K is the more demanding grade, with a minimum tensile strength of 20 MPa [2,900 psi] versus 14 MPa [2,000 psi], minimum elongation at break of 400% versus 300% and maximum abrasion volume loss of 200 mm3 versus 250 mm3. Compare certified test values rather than grade letters when selecting between them.
5.8 Global Fire-Resistance Standards, Grades and Cross-Reference
Fire-resistance terminology overlaps between regions. The table below cross-references grades, test standards and regional equivalents.
| Level of Fire Compliance | Australia | Europe / DIN | North America (CEMA / MSHA) | Compound Test | System (Belt) Test | Typical Industry Term |
|---|---|---|---|---|---|---|
| No fire requirement | AS 1332 Grades M, N, A | DIN 22102 Grades X, Y, W | RMA Grade I, Grade II | Standard tensile and abrasion only | None | "General purpose" or "non-fire-rated" |
| Basic fire retardancy (above-ground) | AS 1332 Grade F (fire resistant), with Grade E (static conducting) where required | DIN 22102 Grade K / DIN 22109 with ISO 340 | MSHA 2G (above-ground). No CEMA rubber grade letter. | DIN 22102 Grade K (minimum tensile 20 MPa [2,900 psi], minimum elongation 400%, maximum abrasion 200 mm3) | ISO 340 laboratory flame test only | "Fire retardant," "semi-FRAS," or "ISO 340 rated" |
| Full underground FRAS | AS 1332 Grade S with AS 4606 certification | DIN 22102 Grade K / DIN 22109 with EN 14973 certification | MSHA Part 14 approval (specific to each belt construction) | DIN 22102 Grade K or equivalent CR-based compound | Gallery fire test, drum friction test (AS/EN) and surface electrical resistance (AS/EN). MSHA requires flame tests only. | "FRAS," "self-extinguishing," "underground rated" |
| Service Level | Australia (AS 1332) | International (ISO 10247) | Europe (DIN 22102) | North America (RMA/CEMA) |
|---|---|---|---|---|
| Severe impact, cut and gouge | Grade M | Category H | Grade X | RMA Grade I |
| Heavy-to-medium abrasion | Grade N | Category L | Grade Y | RMA Grade II |
| Severe sliding abrasion | Grade A (SAR) | Category D | Grade W | No direct equivalent |
Specification must distinguish between compound formulation and system-level performance. DIN Grade K and AS Grade S are rubber compound specifications defining the cover chemistry. A fire-rated compound alone does not make a fire-rated belt. The complete construction (compound, carcass, covers and splicing method) must be tested and certified as a system. A DIN K-compliant compound may fail system-level gallery fire tests (e.g. EN 14973) if the internal carcass allows flame propagation. System-level certification (AS 4606, EN 14973 or MSHA Part 14) is mandatory for underground and enclosed hazardous service.
AS 4606 (Australia), EN 14973 (Europe) and MSHA Part 14 (USA) are not mutually recognised. A belt certified to EN 14973 is not accepted under AS 4606 without explicit approval from the relevant state mines inspectorate. A belt operating in multiple jurisdictions must be independently tested and certified to each applicable standard, or carry written regulatory exemptions from each authority.
The term "semi-FRAS" has no formal standard definition. It typically refers to a belt that passes the ISO 340 laboratory flame test but has not been gallery-fire-tested. ISO 340 is a small-scale, low-energy test in still air, whereas an underground mine fire involves forced ventilation airflow of 1.0 to 3.0 m/s [200 to 590 fpm] through a confined tunnel supplying oxygen to the flame front. Passing ISO 340 therefore does not demonstrate resistance to flame propagation along a full belt. ISO 340-rated belts must not be substituted for AS 4606, EN 14973 or MSHA Part 14 certified belts in underground or enclosed hazardous environments. State the required test certification and regulatory jurisdiction in the procurement specification.
DIN K compounds are produced on CR or SBR bases.
CR-based compounds use chlorine atoms in the backbone to achieve inherent self-extinguishing properties, low flame propagation and lower abrasion volume loss than SBR-based DIN K (volume loss typically 130 to 160 mm3). The service temperature range is limited to minus 10 to 110 deg C [14 to 230 deg F].
SBR-based compounds achieve DIN K fire retardancy through inorganic fillers (alumina trihydrate, magnesium hydroxide or antimony trioxide) synergised with halogenated organic compounds. These fillers reduce tensile strength, elongation and abrasion resistance, and typically leave the compound near the DIN limits (abrasion 180 to 200 mm3). Advantages are a wider cold-weather range (minus 30 to 70 deg C [minus 22 to 158 deg F]) and lower cost. The limitation is lower fire performance.
Where the belt requires EN 14973 underground FRAS certification, specify a CR-based DIN K compound. For above-ground ISO 340 fire retardancy only, an SBR-based DIN K compound is acceptable at lower cost, provided anti-static performance is confirmed on the test certificate.
The DIN 22102 maximum abrasion volume loss for Grade K (200 mm3) is 33% higher than Grade Y (150 mm3) and 122% higher than Grade W (90 mm3). At these limits, a DIN K top cover handling abrasive iron ore fines wears approximately 33% faster than an equivalent-thickness DIN Y cover. Where a fire-rated belt is required in a heavily abrasive application, increase top cover thickness by approximately one third compared with a Grade Y belt to achieve equivalent service life.
Above-ground coal handling facilities frequently specify DIN K with ISO 340 even where no underground FRAS regulation applies. The cost premium over DIN Y is typically 10% to 20% per metre (indicative). Specify DIN K with ISO 340 as the minimum for any enclosed gallery handling combustible bulk material.
6. Cover Gauges and Qualities
The top cover resists impact, abrasion, cutting and gouging from the load. The bottom (pulley-side) cover resists abrasion and friction from idlers and drive pulleys.
Disproportionate cover wear relative to carcass fatigue indicates insufficient cover thickness or suboptimal grade selection. Conversely, carcass failure with substantial cover remaining indicates excessive cover thickness or an under-rated carcass. Match cover wear life to carcass fatigue life.
6.1 Considerations for Selection
Select belt grade and cover thickness against the following factors:
- Type and Abrasiveness of Material: Fine, sharp materials (glass cullet, iron ore fines) require high abrasion resistance and limited impact protection, whereas large lumps (ROM rock, primary crushed ore) require thick, gouge-resistant covers.
- Loading Kinematics: Material trajectory and free-fall height directly dictate the required top cover thickness to mitigate impact penetration.
- Cycle Frequency: Shorter conveyors pass each belt section through the loading zone more frequently, necessitating thicker covers to achieve equivalent wear life.
- Operating Environment: Fire resistance, anti-static, oil resistance and heat resistance requirements.
- Availability and Cost: Non-standard cover thicknesses can increase lead times and minimum order quantities.
6.2 Cycle Time Calculation
Cycle time (T_c), the period of one complete belt revolution, is a primary input to cover thickness selection.
T_c = (2 * L) / v
Where:
- T_c = Cycle time (s)
- L = Conveyor centre-to-centre length (m)
- v = Belt speed (m/s)
Engineering Takeaway: Each belt section passes the loading zone once per cycle. Halving the cycle time doubles the rate of impact and abrasion exposure, so short conveyors require thicker covers for the same material.
Rules of Thumb:
- Less than 30 seconds: High-frequency cycle. The belt is subject to near-continuous impact loading and requires a thicker cover for the specified lump size.
- 30 to 180 seconds: Standard plant conveyor.
- Greater than 180 seconds: Low-frequency cycle (e.g. overland conveyors). Cover thickness can be reduced, lowering belt mass and power consumption.
6.3 Pulley Side (Bottom) Cover Selection
The bottom cover is not exposed to impact or abrasion from the conveyed material. It is subject to continuous friction against the pulley lagging and idler rolls.
Rule of Thumb: Specify a pulley-side cover of one quarter to one third of the top cover thickness.
Specify the following minimum pulley-side cover thicknesses:
- Light duty (sand, grain, woodchips): 1.5 mm [1/16 in].
- Medium duty (crushed coal, limestone): 3.0 mm [1/8 in].
- Heavy duty (ROM ores, high tension): 5.0 to 6.0 mm [3/16 to 1/4 in].
Where the belt is to be turned over during its service life to use both covers, specify equal top and bottom cover thickness. Where heavily abrasive spillage reaches the return run and is trapped between the belt and the pulleys, increase the bottom cover thickness to protect the carcass.
6.4 Top (Carry Side) Cover Thickness Guidelines
The table below provides a starting point for determining the top cover thickness based on material abrasiveness, maximum lump size and cycle time.
Cover thickness absorbs impact energy. Where the drop height exceeds 1.5 m [5 ft], increase the tabulated cover thickness by 25% to 50% or install an impact bed in the loading zone. Steel cord belts have no transverse fabric layer to arrest a lump penetrating between the cords. For steel cord belts without transverse breakers, add a minimum of 3.0 mm [1/8 in] to the tabulated values.
Where the tabulated thickness exceeds standard manufacturing capability or prevents the belt from troughing, specify a fabric belt with a greater number of thinner plies or a straight-warp construction, reduce the lump size before loading, or reduce belt speed and increase belt width to lengthen the cycle time.
| Cycle Time (s) | Lightly Abrasive (Woodchips, Coal, Grain), Lump Size Less Than 50 mm [2 in], mm [in] | Moderately Abrasive (Sand, Anthracite, Gravel), Lump Size Less Than 125 mm [5 in], mm [in] | Heavily Abrasive (Limestone, Phosphate, Slag), Lump Size Less Than 200 mm [8 in], mm [in] | Extremely Abrasive (Glass Cullet, Granite, Quartz), Lump Size 200 mm [8 in] and Greater, mm [in] |
|---|---|---|---|---|
| Less than 15 | 3 to 5 [1/8 to 3/16] | 7 to 10 [1/4 to 3/8] | 10 to 15 [3/8 to 5/8] | 13 to 23 [1/2 to 7/8] |
| 30 | 3 to 4 [1/8 to 5/32] | 5 to 8 [3/16 to 5/16] | 8 to 12 [5/16 to 1/2] | 10 to 18 [3/8 to 3/4] |
| 60 | 2 to 3 [1/16 to 1/8] | 5 to 6 [3/16 to 1/4] | 6 to 10 [1/4 to 3/8] | 9 to 15 [3/8 to 5/8] |
| 120 | 2 to 3 [1/16 to 1/8] | 4 to 6 [5/32 to 1/4] | 6 to 9 [1/4 to 3/8] | 8 to 13 [5/16 to 1/2] |
| Greater than 180 | 1 to 2 [1/32 to 1/16] | 4 to 5 [5/32 to 3/16] | 5 to 8 [3/16 to 5/16] | 7 to 12 [1/4 to 1/2] |
6.5 Energy Saving (Low Rolling Resistance) Covers
On long horizontal conveyors, bottom cover indentation rolling resistance constitutes a major portion of total system power consumption. Due to viscoelastic hysteresis, rubber deformation over the idlers absorbs kinetic energy, dissipating it as heat.
Indentation resistance depends strongly on ambient temperature. Below freezing, polymer chain mobility reduces. At minus 30 deg C [minus 22 deg F], standard compounds stiffen, increasing indentation resistance and power consumption.
A low rolling resistance (LRR) bottom cover on a horizontal conveyor longer than 1,000 m [3,300 ft] can reduce indentation rolling resistance by 10% to 20%. The resulting reduction in T_max can permit a lower-rated carcass (e.g. EP 800/4 in place of EP 1000/4). Specify cold-weather LRR compounds for sub-zero operation. These use plasticisers to maintain polymer flexibility down to minus 40 deg C [minus 40 deg F].
LRR compounds typically have lower abrasion resistance and tear strength than standard grades. They are rarely justified on short plant conveyors, where lift and secondary resistances dominate the tension calculation.
7. Solid Woven Belting
Solid woven belting replaces discrete fabric plies bonded with rubber skim coats with a single interlocked weave of synthetic fibres impregnated with PVC. With no individual plies, it cannot delaminate, which makes it the common construction for underground coal mining, potash mining and other enclosed, high-hazard environments where fire resistance and anti-static performance are regulated.
7.1 Belt Construction
Solid Woven belting consists of three main components. The textile carcass is typically woven with polyester or nylon load-bearing warp (longitudinal) fibres and nylon or nylon/cotton weft (transverse) fibres, with synthetic binder yarns locking the warp and weft together. High-tenacity continuous filament yarns provide the tension rating, while the interlocking cotton/nylon weft provides impact resistance and a dense matrix that retains mechanical fasteners.
PVC impregnation follows weaving. The textile passes through a liquid PVC plastisol bath under tension, saturating the matrix and displacing moisture and air. The PVC is formulated with plasticisers, ultraviolet (UV) stabilisers and fire retardants and renders the carcass resistant to moisture, acidic mine water, bacteria and oils.
Cover materials complete the construction. Standard PVC covers up to 3 mm [1/8 in] per side can be applied integrally during manufacture. Because PVC has a lower coefficient of friction than rubber, PVC-covered belts can slip on drive pulleys without ceramic lagging and are prone to material rollback on inclines steeper than 12 to 14 deg. Where higher friction or greater abrasion resistance is needed, rubber (nitrile/SBR) covers can be bonded to the PVC carcass, typically to a maximum of 6 mm [1/4 in] top and 2 mm [5/64 in] bottom.
7.2 Operating Temperature Range
Thermoplastic-based Solid Woven belts exhibit higher sensitivity to thermal extremes compared to vulcanised elastomeric belts. Standard PVC compounds experience structural degradation at 70 to 80 deg C [158 to 176 deg F]. Exceeding this range induces matrix softening, loss of transverse stiffness, collapse into the idler junctions and degraded mechanical fastener retention. Limit continuous service to 70 deg C [158 deg F] and short-term peaks to 90 deg C [194 deg F]. Do not use PVC-covered Solid Woven belts for hot materials such as clinker or hot sinter.
Standard PVC compounds become stiff and brittle at approximately minus 15 deg C [5 deg F]. Specify cold-weather plastisol formulations for service down to minus 40 deg C [minus 40 deg F] to resist cracking at the pulleys, and state the minimum operating temperature in the purchase specification.
7.3 Belt Designations and Data
The table below correlates imperial (lbf/in) class designations with metric (kN/m) strength ratings and lists generic thicknesses and masses.
| Belt Designation (PIW Class) | Rated Working Tension kN/m [PIW] | Minimum Ultimate Warp Strength kN/m [PIW] | Minimum Ultimate Weft Strength kN/m [PIW] | Nominal Thickness mm [in] | Nominal Mass kg/m2 [lb/ft2] |
|---|---|---|---|---|---|
| 3000 | 50 [286] | 500 [2,850] | 245 [1,400] | 7.7 [0.30] | 10.5 [2.15] |
| 3500 | 63 [360] | 630 [3,600] | 263 [1,500] | 8.1 [0.32] | 11.0 [2.25] |
| 4000 | 70 [400] | 700 [4,000] | 263 [1,500] | 8.4 [0.33] | 11.0 [2.25] |
| 4500 | 80 [457] | 800 [4,570] | 315 [1,800] | 8.5 [0.33] | 11.0 [2.25] |
| 5000 | 87 [500] | 875 [5,000] | 320 [1,825] | 9.0 [0.35] | 11.3 [2.31] |
| 6000 | 105 [600] | 1,050 [6,000] | 350 [2,000] | 9.6 [0.38] | 11.7 [2.40] |
| 6500 | 114 [650] | 1,140 [6,500] | 350 [2,000] | 9.6 [0.38] | 12.1 [2.48] |
| 7000 | 125 [714] | 1,250 [7,140] | 350 [2,000] | 10.5 [0.41] | 13.0 [2.66] |
| 8000 | 140 [800] | 1,400 [8,000] | 350 [2,000] | 11.3 [0.44] | 14.4 [2.95] |
| 10000 | 175 [1,000] | 1,750 [10,000] | 450 [2,570] | 13.1 [0.52] | 15.9 [3.26] |
| 12000 | 210 [1,200] | 2,100 [12,000] | 450 [2,570] | 14.0 [0.55] | 18.5 [3.79] |
| 15000 | 262 [1,500] | 2,625 [15,000] | 450 [2,570] | 15.3 [0.60] | 19.6 [4.01] |
| 18000 | 315 [1,800] | 3,150 [18,000] | 450 [2,570] | 17.6 [0.69] | 23.8 [4.87] |
Note: Tabulated values are generic baselines. For heavy impact or high-tension mechanical fasteners, specify a reinforced-weft construction. Reinforced weft increases nominal thickness and mass. The nominal thickness and mass are based on 1 mm [0.04 in] PVC covers on each side. For thicker rubber covers, add 1.4 kg/m2 [0.29 lb/ft2] per millimetre of cover.
7.4 Solid Woven Troughability
Solid woven belts are generally more transversely flexible than equivalent-tension multi-ply belts because the single interlocked weave has no inter-ply rubber layers. Transverse stiffness increases with carcass thickness and tension rating, increasing the minimum belt width required to conform to the trough.
The table below gives the minimum belt width for empty-belt contact with the centre roll.
| Belt Designation (PIW Class) | Nominal Thickness mm [in] | 20 deg Trough mm [in] | 35 deg Trough mm [in] | 45 deg Trough mm [in] |
|---|---|---|---|---|
| 3000 to 4500 | 7.7 to 8.5 [0.30 to 0.33] | 350 [14] | 400 [16] | 450 [18] |
| 5000 to 6500 | 9.0 to 9.6 [0.35 to 0.38] | 400 [16] | 450 [18] | 500 [20] |
| 7000 to 8000 | 10.5 to 11.3 [0.41 to 0.44] | 450 [18] | 500 [20] | 600 [24] |
| 10000 to 12000 | 13.1 to 14.0 [0.52 to 0.55] | 500 [20] | 600 [24] | 750 [30] |
| 15000 to 18000 | 15.3 to 17.6 [0.60 to 0.69] | 600 [24] | 750 [30] | 900 [36] |
Note: Solid woven belts with bonded rubber covers (up to 6 mm [1/4 in] top and 2 mm [5/64 in] bottom) are stiffer than PVC-covered belts. Where total rubber cover exceeds 4 mm [5/32 in], increase the minimum width to the next tabulated value. Confirm values with the belt manufacturer.
8. Steel Cord Belting
Steel cord belting is the highest-tension standard construction for bulk handling. It is used on conveyors where high belt tension, limited take-up travel or the requirement for a high elastic modulus makes a fabric multi-ply belt unsuitable.
Steel cord belts carry a higher initial cost than fabric belting but provide high splice efficiency, smaller pulleys relative to tension rating and reduced take-up travel owing to low elongation.
8.1 Construction and Designations
Steel cord belts consist of a single layer of evenly spaced, zinc-galvanised high-tensile steel wire ropes (cords) embedded in a bonding rubber matrix and protected by top and bottom rubber covers. The ST prefix is followed by the ultimate breaking strength in kN/m (e.g. ST 2000 denotes 2,000 kN/m [11,400 PIW]).
With no transverse fabric plies to arrest a sharp lump penetrating the cover, ST belts require a thicker top cover than fabric belts. Specify a top cover of at least 1.5 times the cord diameter.
| Designation (kN/m) | Cord Diameter mm [in] | Cord Pitch (Spacing) mm [in] | Base Belt Mass kg/m2 [lb/ft2] | Nominal Thickness mm [in] |
|---|---|---|---|---|
| ST 500 | 2.6 [0.10] | 13.8 [0.54] | 14.1 [2.89] | 10.6 [0.42] |
| ST 630 | 3.1 [0.12] | 13.8 [0.54] | 15.0 [3.07] | 10.8 [0.43] |
| ST 800 | 3.4 [0.13] | 13.8 [0.54] | 16.4 [3.36] | 11.4 [0.45] |
| ST 1000 | 4.0 [0.16] | 15.3 [0.60] | 17.9 [3.67] | 12.0 [0.47] |
| ST 1250 | 4.5 [0.18] | 15.3 [0.60] | 21.8 [4.46] | 14.5 [0.57] |
| ST 1400 | 5.0 [0.20] | 15.3 [0.60] | 22.8 [4.67] | 14.8 [0.58] |
| ST 1600 | 5.5 [0.22] | 17.3 [0.68] | 24.4 [5.00] | 15.5 [0.61] |
| ST 2000 | 6.4 [0.25] | 17.3 [0.68] | 27.2 [5.57] | 16.4 [0.65] |
| ST 2500 | 7.4 [0.29] | 19.4 [0.76] | 32.4 [6.64] | 19.4 [0.76] |
| ST 3150 | 8.6 [0.34] | 19.4 [0.76] | 36.8 [7.54] | 20.6 [0.81] |
| ST 3500 | 9.1 [0.36] | 19.4 [0.76] | 39.5 [8.09] | 21.8 [0.86] |
| ST 4000 | 9.8 [0.39] | 19.4 [0.76] | 43.7 [8.95] | 23.8 [0.94] |
| ST 4500 | 10.4 [0.41] | 19.4 [0.76] | 47.0 [9.63] | 25.4 [1.00] |
| ST 5000 | 11.0 [0.43] | 19.4 [0.76] | 51.2 [10.5] | 27.0 [1.06] |
| ST 5400 | 11.6 [0.46] | 20.0 [0.79] | 55.0 [11.3] | 28.6 [1.13] |
| ST 6300 | 12.8 [0.50] | 20.0 [0.79] | 61.1 [12.5] | 30.8 [1.21] |
| ST 7000 | 13.5 [0.53] | 22.0 [0.87] | 66.0 [13.5] | 33.0 [1.30] |
| ST 7500 | 14.0 [0.55] | 22.0 [0.87] | 70.0 [14.3] | 34.5 [1.36] |
| ST 8000 | 14.8 [0.58] | 22.0 [0.87] | 74.0 [15.2] | 36.0 [1.42] |
| ST 8500 | 15.2 [0.60] | 24.0 [0.94] | 78.0 [16.0] | 37.5 [1.48] |
| ST 9000 | 15.8 [0.62] | 24.0 [0.94] | 82.0 [16.8] | 39.0 [1.54] |
| ST 10000 | 17.0 [0.67] | 24.0 [0.94] | 90.0 [18.4] | 42.0 [1.65] |
Note: Belt mass is based on standard minimum covers. Add 1.15 kg/m2 [0.24 lb/ft2] for every 1 mm [0.04 in] of additional cover rubber. ST ratings above ST 6300 are engineered-to-order for specific projects. Cord diameters, pitches and belt masses for ST 7000 and above are indicative and vary between manufacturers with cord construction (e.g. 7x7, 7x19 or 7x36 wire rope lay), steel grade (1,770 MPa [257 ksi] or 1,960 MPa [284 ksi]) and cover thickness requirements. Obtain project-specific data sheets from the belt manufacturer for all ST ratings above ST 6300.
8.2 Operating Conditions and Safety Factors
Dynamic modelling, soft-start variable frequency drives (VFDs) and active take-up winches permit overland conveyors to operate at reduced safety factors (e.g. 5.5:1 or 4.5:1). Reduced safety factors lower the required ST rating, belt mass and drive acceleration torque. DOL starting requires a minimum 6.7:1 safety factor to accommodate transient tension peaks and limit the risk of splice failure.
Use safety factors of 4.5:1 and 5.5:1 only where the conveyor is equipped with controlled soft-start drives (VFD or fluid coupling), the system has been dynamically modelled to confirm transient tensions during starting and stopping and the splice design has been verified for the actual peak tension. Select the safety factor appropriate to the installed drive and control system. The table below gives the allowable working tension for each ST rating at each safety factor (SF).
| Designation | Working Tension at 6.7:1 SF kN/m [PIW] | Working Tension at 5.5:1 SF kN/m [PIW] | Working Tension at 4.5:1 SF kN/m [PIW] |
|---|---|---|---|
| ST 500 | 75 [426] | 91 [519] | 111 [634] |
| ST 630 | 94 [537] | 115 [654] | 140 [799] |
| ST 800 | 119 [682] | 145 [831] | 178 [1,020] |
| ST 1000 | 149 [852] | 182 [1,040] | 222 [1,270] |
| ST 1250 | 187 [1,070] | 227 [1,300] | 278 [1,590] |
| ST 1400 | 209 [1,190] | 255 [1,450] | 311 [1,780] |
| ST 1600 | 239 [1,360] | 291 [1,660] | 356 [2,030] |
| ST 2000 | 299 [1,700] | 364 [2,080] | 444 [2,540] |
| ST 2500 | 373 [2,130] | 455 [2,600] | 556 [3,170] |
| ST 3150 | 470 [2,680] | 573 [3,270] | 700 [4,000] |
| ST 3500 | 522 [2,980] | 636 [3,630] | 778 [4,440] |
| ST 4000 | 597 [3,410] | 727 [4,150] | 889 [5,080] |
| ST 4500 | 672 [3,840] | 818 [4,670] | 1,000 [5,710] |
| ST 5000 | 746 [4,260] | 909 [5,190] | 1,111 [6,340] |
| ST 5400 | 806 [4,600] | 982 [5,610] | 1,200 [6,850] |
| ST 6300 | 940 [5,370] | 1,145 [6,540] | 1,400 [7,990] |
| ST 7000 | 1,045 [5,970] | 1,273 [7,270] | 1,556 [8,880] |
| ST 7500 | 1,119 [6,390] | 1,364 [7,790] | 1,667 [9,520] |
| ST 8000 | 1,194 [6,820] | 1,455 [8,310] | 1,778 [10,150] |
| ST 8500 | 1,269 [7,240] | 1,545 [8,820] | 1,889 [10,790] |
| ST 9000 | 1,343 [7,670] | 1,636 [9,340] | 2,000 [11,420] |
| ST 10000 | 1,493 [8,520] | 1,818 [10,380] | 2,222 [12,690] |
8.3 Troughability
Steel cord belts have no transverse fabric layer and therefore low transverse rigidity, which facilitates troughing. Transverse stiffness increases with cord diameter and cover thickness at higher ST ratings. A belt narrower than the tabulated minimum for its ST rating will not contact the centre roll.
| Designation | 20 deg Trough mm [in] | 35 deg Trough mm [in] | 45 deg Trough mm [in] |
|---|---|---|---|
| ST 500 to 1000 | 600 [24] | 600 [24] | 750 [30] |
| ST 1250 to 1400 | 600 [24] | 750 [30] | 900 [36] |
| ST 1600 to 2500 | 750 [30] | 900 [36] | 900 [36] |
| ST 3150 to 4500 | 900 [36] | 900 [36] | 1,050 [42] |
| ST 5000 to 6300 | 900 [36] | 1,050 [42] | 1,200 [48] |
| ST 7000 to 8000 | 1,050 [42] | 1,200 [48] | 1,350 [54] |
| ST 8500 to 10000 | 1,200 [48] | 1,350 [54] | 1,500 [60] |
Note: Where the belt has a transverse steel or fabric breaker for rip protection, add 150 mm [6 in] to the minimum width.
9. Specialty Belt Configurations
Specialty belt configurations address conveying requirements beyond standard flat or troughed profiles: steep inclines, tight curves, vertical lifting and dust containment. Selection depends on conveying angle, material characteristics and routing geometry.
| Belt Type | Use Case | Maximum Incline | Construction | Rule of Thumb | Failure Mode |
|---|---|---|---|---|---|
| Pipe / Tube | Enclosed conveying, dust control, tight horizontal curves | Moderate | Flat belt formed into a tube by hexagonal idler panels. Overlap seam on top. | Maximum lump size one third of pipe diameter. Pipe diameter approximately one third of flat belt width. Minimum horizontal curve radius 300 to 600 times pipe diameter. | Seam inversion leading to material discharge |
| Corrugated Sidewall | Steep to vertical incline, compact footprint | Up to 90 deg | Cross-rigid base belt (monofilament weft plies), corrugated sidewalls and transverse cleats | Maximum cleat spacing 2 to 3 times cleat height (free-flowing) and 1.0 to 1.5 times cleat height (wet or cohesive) | Base belt deformation over return idlers |
| Chevron / Cleated | Incline rollback prevention without full sidewalls | 18 to 30 deg | Moulded cleats typically 15 to 32 mm [5/8 to 1-1/4 in] high. Open (V) or closed (Y or herringbone). | Open (V) for coarse or dry material. Closed (Y or herringbone) for fine, wet or sticky material. Cohesive materials clog either profile. | Material lateral slip (incorrect profile selection) or clogging |
| Bucket Elevator | Vertical lifting | Vertical (90 deg) | Solid woven (PVC) or straight-warp carcass with high fastener pull-out resistance | Bolt-fastened buckets require reinforcing back-plates to distribute clamping forces | Fastener pull-through causing bucket detachment |
| Air-Supported | Dust or environmentally sensitive duties (grain, cement, food) or low rolling resistance | 10 to 12 deg | A sealed plenum replaces the carry idlers. The belt is supported on an air film. | Straight routes only | Mistracking owing to the absence of steering idlers. Tracking relies entirely on trough geometry and uniform tension. |
| Sandwich (Pressing) | High-angle conveying of fragile or sized material (hot briquetted iron or aggregate) | Up to 90 deg | Two belts face-to-face confine the material without cleats or sidewalls | Contact pressure 2 to 10 kPa [0.3 to 1.5 psi], controlled by the spacing and angle of the pressing idlers | Material slip (insufficient pressure) or product degradation (excessive pressure) |
10. Belt Manufacturing Tolerances
Conveyor belting is manufactured to specified dimensional tolerances. Distinguish tracking deviations caused by structural misalignment from those caused by out-of-specification belt geometry.
10.1 Width Tolerance
AS 1332, ISO 251 and DIN 22102 specify consistent width tolerances.
- Belts up to 500 mm [20 in] wide: The allowable tolerance is +/- 5.0 mm [3/16 in].
- Belts over 500 mm [20 in] wide: The allowable tolerance is +/- 1.0% of the nominal specified width.
10.2 Total Thickness Tolerance
AS 1332, ISO 14890 and DIN 22102 specify the following total belt thickness (carcass and covers) tolerances.
- Belts with a total thickness of 10 mm [3/8 in] or less: The tolerance is +/- 1.0 mm [0.04 in].
- Belts thicker than 10 mm [3/8 in]: The tolerance is +/- 10% of the total specified thickness.
10.3 Cover Thickness and Zero Negative Specifications
Standard tolerances permit positive and negative cover thickness deviation. AS 1332, ISO 14890 and DIN 22102 permit +1.0 mm [0.04 in] to minus 0.2 mm [0.008 in] for covers up to 4.0 mm [5/32 in] thick and generally +/- 5.0% for thicker covers.
Cover thickness is measured from the outer surface to the first reinforcing ply or cord layer and therefore includes the skim coat bonding the cover to the carcass. A manufacturer applying the full negative tolerance (e.g. minus 5.0%) and counting the skim coat as cover delivers less wear rubber than specified, reducing wear life in proportion.
For heavily abrasive applications such as iron ore, crushed granite or glass cullet, specify a "Zero Negative Cover Tolerance" during procurement. This clause overrides standard ISO/DIN average thickness and localised deviation allowances. It contractually binds the manufacturer to a (+X, minus 0) tolerance at all measurable points across the belt width.
10.4 Straightness (Camber / Bow)
A conveyor belt must be manufactured straight along its length. A permanent lateral curve (camber or bow) induces persistent asymmetric tracking irrespective of structural alignment. The maximum permissible camber per ISO 14890 / DIN 22102 is 0.5% of the measured length. Over a 10 m [33 ft] sample laid flat, the belt edge must not deviate from a straight line by more than 50 mm [2 in].